3M X55I Operation Guide - Page 17

Power on/off - projector lamp

Get 3M X55I PDF manuals and user guides View all 3M X55I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3M™ Digital Projector S55i/X55i Power on/off Power on/off WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole. NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices. Turning on the power 1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet. 2. Remove the lens cover, and set the power switch to the ON position. The power indicator will light up in steady orange. Then wait several seconds because the buttons may not function for these several seconds. STANDBY/ON button VIDEO STANDBY/ON RGB SEARCH ASPECT AUTO BLANK MAGNIFY ON HOME PAGE UP VOLUME END PAGE DOWN MUTE OFF FREEZE KEYSTONE POSITION MENU ESC ENTER RESET POWER indicator 3. Press the STANDBY/ON button on the projector or the remote control. The projector lamp will light up and the POWER POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green. To display the picture, select an input signal according to (Steady orange) POWER (Blinking in green) the section "Selecting an input signal" (18). POWER Turning off the power (Steady green) This product is able to turn off the main power during the cooling. However, please pay special attention to below two points when you do: (1) Please do not turn the projector on again for at least 1 minute in this case. Neglect could shorten the lifetime of the lamp. (2) During use or immediately after use, do not touch around the lamp and vents of the projector (4 ) It could cause a burn. 1. Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for approximately 5 seconds. 2. Press the STANDBY/ON button on the projector or the remote control again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. Power off? POWER Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete. 3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. Attach the lens cover. (Blinking in orange) POWER (Steady orange) © 3M 2005. All Rights Reserved. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
17
Power on/off
Power on/off
WARNING
►
When the power is on, a strong light is emitted. Do not look into
the lens of projector. Also do not peep at the inside of projector through a hole.
NOTE
•
Turn the power on/off in right order. Please power on the projector prior
to the connected devices. Power off the projector later than the connected devices.
Turning on the power
1.
Make sure that the power cord is firmly and
correctly connected to the projector and the
outlet.
2.
Remove the lens cover, and set the power
switch to the ON position.
The power indicator will light up in steady orange.
Then wait several seconds because the buttons
may not function for these several seconds.
3.
Press the STANDBY/ON button on the projector or the remote control.
The projector lamp will light up and the POWER
indicator will begin blinking in green. When the power is
completely on, the indicator will stop blinking and light in
green.
To display the picture, select an input signal according to
the section "Selecting an input signal"
(
18
)
.
Turning off the power
This product is able to turn off the main power during the cooling. However, please
pay special attention to below two points when you do:
(1) Please do not turn the projector on again for at least 1 minute in this case.
Neglect could shorten the lifetime of the lamp.
(2) During use or immediately after use, do not touch around the lamp and vents
of the projector
(
4
)
It could cause a burn.
1.
Press the STANDBY/ON button on the projector or the remote control.
The message "Power off?" will appear on the screen for approximately 5
seconds.
2.
Press the STANDBY/ON button on the projector or the
remote control again while the message appears.
The projector lamp will go off, and the POWER indicator will
begin blinking in orange.
Then the POWER indicator will stop blinking and light in
steady orange when the lamp cooling is complete.
3.
Make sure that the power indicator lights in steady orange,
and set the power switch to the OFF position. The POWER
indicator will go off. Attach the lens cover.
POWER
(Steady orange)
POWER
(Blinking in green)
POWER
(Steady green)
STANDBY/ON
button
POWER
indicator
Power off?
POWER
(Blinking in orange)
POWER
(Steady orange)
3M™
Digital
Projector S
5
5
i/X55i
© 3M 200
5.
All Rights Reserved.