3M X55I Operation Guide - Page 48

Phenomena that may be easy to be mistaken for machine defects

Get 3M X55I PDF manuals and user guides View all 3M X55I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

3M™ Digital Projector S55i/X55i Troubleshooting Phenomena that may be easy to be mistaken for machine defects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company. 1. Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem. If the situation cannot be corrected, 2. The projector's microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart. 3. Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the OPTION menu (39) to reset all settings to factory default. Then, if the problem is not removed after the remedy, please contact your dealer or service company. Phenomenon Cases not involving a machine defect Reference page The electrical power cord is not plugged in. Correctly connect the power cord. 14 The power switch is not set to the on position. Set the power switch to [ | ] (On). 17 The main power source has been interrupted during Power does not operation such as by a power outage (blackout), etc. Please turn the power off, and allow the projector to cool 17 come on. down at least 2 minutes, then turn the power on again. Either there is no lamp and/or lamp door, or either of these has not been properly fixed. Please turn the power off, and allow the projector to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp door, and then turn the power on again. 40, 41 The signal cables are not correctly connected. Correctly connect the connection cables. 12, 13 Signal source does not correctly work. Neither sounds Correctly set up the signal source device by referring to the manual of the source device. - nor pictures are outputted. The input changeover settings are mismatched. Select the input signal, and correct the settings. 18 The RGB IN2 port is assigned to an RGB out while an RGB input signal is inputted to the port. 12 Push the RGB IN OUT switch to switch the function of the port. 48 © 3M 2005. All Rights Reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
48
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
WARNING
►Never use the projector if abnormal operations such as
smoke, strange odor, excessive sound, damaged casing or elements or cables,
penetration of liquids or foreign matter, etc. should occur. In such cases,
immediately turn off the power switch and then disconnect the power plug from
the power outlet. After making sure that the smoke or odor has stopped, contact
your dealer or service company.
1.
Before requesting repair, please check in
accordance with the following chart. This
operation sometimes resolves your problem.
If the situation cannot be corrected,
2.
The projector’s microprocessor may need to be
reset. Please push the Restart switch by using a
cocktail stick or similar and the projector will restart.
3.
Some setting may be wrong. Please use the FACTORY RESET function of the
SERVICE item in the OPTION menu
(
39
)
to reset all settings to factory default.
Then, if the problem is not removed after the remedy, please contact your dealer
or service company.
Phenomenon
Cases not involving a machine defect
Reference
page
Power does not
come on.
The electrical power cord is not plugged in.
Correctly connect the power cord.
14
The power switch is not set to the on position.
Set the power switch to [ | ] (On).
17
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Please turn the power off, and allow the projector to cool
down at least 2 minutes, then turn the power on again.
17
Either there is no lamp and/or lamp door, or either of
these has not been properly fixed.
Please turn the power off, and allow the projector to cool down
at least 45 minutes. After the projector has sufficiently cooled
down, please make confirmation of the attachment state of the
lamp and lamp door, and then turn the power on again.
40, 41
Neither sounds
nor pictures are
outputted.
The signal cables are not correctly connected.
Correctly connect the connection cables.
12, 13
Signal source does not correctly work.
Correctly set up the signal source device by referring to the
manual of the source device.
–
The input changeover settings are mismatched.
Select the input signal, and correct the settings.
18
The RGB IN2 port is assigned to an RGB out while
an RGB input signal is inputted to the port.
Push the RGB IN OUT switch to switch the function of the port.
12
3M™
Digital
Projector S
5
5
i/X55i
© 3M 200
5.
All Rights Reserved.