AIWA CX-NMT50 Operating Instructions - Page 22

Setting, The Clock, The Timer

Get AIWA CX-NMT50 PDF manuals and user guides View all AIWA CX-NMT50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

SETTING THE CLOCK SETTING THE TIMER 2,3 1,2,3 1 1 2,4 3 1,2 6 7 Press the CLOCK button on the remote control, and press the II SET button within 4 seconds. 2 Press the + DOWN or > UP button to designate the hour, and press the II SET button. The hour stops flashing and the minute starts flashing. 3 Press the + DOWN or - UP button to designate the minute, and press the II SET button. The minute stops flashing on the display and the clock starts from 00 seconds. To display the current time Press the CLOCK button on the remote control. The time is displayed for 4 seconds. However, the time cannot be displayed during recording. To switch to the 24-hour standard Press the CLOCK button on the remote control and then press the s button within 4 seconds. Repeat the same procedure to restore the 12-hour standard. If the clock display flashes This is caused by a power interruption. The current time needs to be reset. If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be reset. The unit can be turned on at a specified time every day with the built-in timer. Preparation Make sure the clock is set correctly. Use the remote control 1 Press the TIMER button repeatedly until @ appears on the display, and press the II SET button within 4 seconds. @ is displayed, and the hour flashes. o If you press the II SET button after 4 seconds, another operation may start. 2 Designate the hour of the timer-on time by pressing the M-4 DOWN or M UP button, and press the II SET button, Repeat to designate the minute of the timer-on time. After you designate the timer-on time, one of the source name flashes on the display for 4 seconds. 3 Within 4 seconds, press one of the function buttons to select a source. The selected source name flashes for 4 seconds. At this time, the selected function button does not light up. q If this step is not completed within 4 seconds, repeat from step 1. q If the TUNER button is pressed, the band cannot be selected in this step. 4 Within 4 seconds, select the duration for the timer-activated period with the H DOWN or FH UP button. 21 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SETTING
THE CLOCK
SETTING
THE TIMER
2,3
1,2,3
1
7 Press the CLOCK
button
on the remote
control,
and press the
II
SET button
within
4 seconds.
2
Press
the
+
DOWN
or
>
UP
button
to
designate
the hour, and press the II
SET button.
The hour stops flashing and the minute starts flashing.
3
Press
the
+
DOWN
or
-
UP
button
to
designate
the
minute,
and
press
the
II
SET
button.
The minute stops flashing on the display and the clock starts
from 00 seconds.
To display the current time
Press the CLOCK
button on the remote control.
The time is
displayed
for 4 seconds.
However, the time cannot be displayed
during recording.
To switch to the 24-hour standard
Press the CLOCK button on the remote control and then press
the
button within 4 seconds.
Repeat the same procedure
to restore the 12-hour standard.
If the clock display flashes
This is caused by a power interruption. The current time needs
to be reset.
If power is interrupted
for more than approximately
24 hours,
all settings stored in memory after purchase need to be reset.
1
2,4
3
1,2
6
The unit can be turned on at a specified time every day with the
built-in timer.
Preparation
Make sure the clock is set correctly.
Use the remote control
1
2
3
4
Press
the
TIMER
button
repeatedly
until
@
appears
on the
display,
and
press
the
II
SET
button
within
4 seconds.
@
is displayed,
and the hour flashes.
o
If you press the
II
SET button
after 4 seconds,
another
operation
may start.
Designate
the
hour
of
the
timer-on
time
by
pressing
the
M-4
DOWN
or M
UP button,
and
press the II
SET button,
Repeat to designate
the
minute
of the timer-on
time.
After you designate the timer-on time, one of the source name
flashes on the display for 4 seconds.
Within
4 seconds,
press
one
of the
function
buttons
to select
a source.
The selected source name flashes for 4 seconds. At this time,
the selected function button does not light up.
If this step is not completed
within 4 seconds,
repeat from
step 1.
If the TUNER button is pressed, the band cannot be selected
in this step.
Within
4 seconds,
select
the
duration
for
the
timer-activated
period with the H
DOWN or FH
UP button.
21
ENGLISH