Acer DV433 User Manual - Page 20

Preparation for installation, Determine the installation location

Get Acer DV433 PDF manuals and user guides View all Acer DV433 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

20 Chapter 2 Preparation for use Chapter 2 Preparation for use Preparation for installation Determine the installation location CAUTION DO NOT ATTEMPT TO INSTALL THE LCD DISPLAY BY YOURSELF. Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. NOTE Proper operation of the display is not guaranteed when it is mounted upside down or face down. CAUTION Lay the protective sheet, which was wrapped around the LCD display when it was packaged, beneath the LCD display so as not to scratch the panel. NOTE The LCD display requirements apply for equipment operating up to 2,000m above sea level. Ventilation requirements for enclosure mounting To allow heat to disperse, leave space around the display. NOTE Don't block the vents in the back of the display shown in the figure on the next page. If they are blocked, heat accumulates inside the display, and can cause breakdown. The upper limit of the operation guaranteed ambient temperature when the display is installed in the landscape position is 40°C (104°F). When installing the monitor in a case or an enclosure, ensure adequate ventilation to keep the temperature inside the case is be 40°C (104°F) or below by providing a cooling fan or ventilation holes in the case.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
20
Chapter 2
Preparation for use
Chapter 2
Preparation for use
Preparation for installation
Determine the installation location
Ventilation requirements for enclosure mounting
To allow heat to disperse, leave space around the display.
DO NOT ATTEMPT TO INSTALL THE LCD DISPLAY BY YOURSELF.
Installing your LCD display must be done by a qualified technician. Contact your dealer for
more information.
Proper operation of the display is not guaranteed when it is mounted upside down or face
down.
Lay the protective sheet, which was wrapped around the LCD display when it was packaged,
beneath the LCD display so as not to scratch the panel.
The LCD display requirements apply for equipment operating up to 2,000m above sea level.
Don’t block the vents in the back of the display shown in the figure on the next page. If they
are blocked, heat accumulates inside the display, and can cause breakdown. The upper limit
of the operation guaranteed ambient temperature when the display is installed in the land-
scape position is 40°C (104°F). When installing the monitor in a case or an enclosure, ensure
adequate ventilation to keep the temperature inside the case is be 40°C (104°F) or below by
providing a cooling fan or ventilation holes in the case.
CAUTION
NOTE
CAUTION
NOTE
NOTE