Asko W600 Service Manual - Page 15

W600 And W620 Test Program And Fault Indications, W600 And W620 Test Program, W600 And W620 Faul - not spinning

Get Asko W600 PDF manuals and user guides View all Asko W600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

W600 AND W620 TEST PROGRAM AND FAULT INDICATIONS W600 AND W620 TEST PROGRAM 1. Insert a jumper into E10 on the programmer 2. S tar t pr ogram 3 (F ast wash). 3. EV2 (inlet valve for main wash water) allows water into the machine up to the washing level. 4. Press the Super Rinse ( ) button. 5. Heat up for 10 minutes or by 50° F (10° C). 6. Press the Economy (E2) button. 7. Add more water to the wool level, about 1-1/2" up the door. 8. Wash for 4 minutes. 9. Wash for 16 minutes, or until the E button is pressed in again. 10. Run a long spin. W600 AND W620 FAULT INDICATIONS If a fault occurs during a program cycle, this is indicated by the program knob stopping in position C or S after the program has finished or been interrupted. Position C If the program knob stops in position " after the program has finished or been interrupted, this indicates that one of the following problems has occurred during the program cycle: Thermistor fault The washing program has finished without heating. 1. Check the fuses. 2. Measure the Ohms (see page 12). Heating element fault The washing program has finished without heating. 1. Check the fuses. 2. Measure the thermistor Ohms. 3. Measure the heater relay Ohms. Programmer fault The washing program has been interrupted. Check the fuses. Water inlet fault In. dicates a fault in the water supply. 1. Make sure the water supply to the machine has been turned on (cold fill only) 2. Check that the filter in the machine water inlet is not blocked. Draining fault Draining has taken too long. Check the drain hose and the drain pump as follows: 1. Make sure an object is not stuck in the drain hose outlet. Clean out the hose. 2. Make sure the drain pump isn't blocked by foreign objects. Clean out the pump. 3. Make sure the drain hose isn't kinked. 4. After solving the problem, run program 10 (Drain). Position S If the program knob stops in position "S" after the program has finished or been interrupted, this indicates that a motor fault, a level sensor fault, or a program fault has occurred during the program cycle. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
15
W600 AND W620 TEST PROGRAM
W600 AND W620 TEST PROGRAM
W600 AND W620 TEST PROGRAM
W600 AND W620 TEST PROGRAM
W600 AND W620 TEST PROGRAM
1.
Insert a jumper into E10 on the programmer
.
2.
S tar t pr ogram 3 (F
ast wash).
3.
EV2 (inlet valve for main wash water) allows
water into the machine up to the washing level.
4.
Press the Super Rinse (
) button.
5.
Heat up for 10 minutes or by 50
°
F (10
°
C).
6.
Press the Economy (
E
2
)
button.
7.
Add more water to the wool level, about 1-1/2
”
up the door.
8.
Wash for 4 minutes.
9. Wash for 16 minutes, or until the
E button is
pressed in again.
10. Run a long spin.
W600 AND W620 FAUL
W600 AND W620 FAUL
W600 AND W620 FAUL
W600 AND W620 FAUL
W600 AND W620 FAULT INDICA
T INDICA
T INDICA
T INDICA
T INDICATIONS
TIONS
TIONS
TIONS
TIONS
If a fault occurs during a program cycle, this is
indicated by the program knob stopping in position
C or S after the program has finished or been
interrupted.
Position C
osition C
osition C
osition C
osition C
If the program knob stops in position
”
after the
program has finished or been interrupted, this
indicates that one of the following problems has
occurred during the program cycle:
Thermistor fault
Thermistor fault
Thermistor fault
Thermistor fault
Thermistor fault
The washing program has finished without heating.
1.
Check the fuses.
2.
Measure the Ohms (see page 12).
Heating element fault
Heating element fault
Heating element fault
Heating element fault
Heating element fault
The washing program has finished without heating.
1.
Check the fuses.
2.
Measure the thermistor Ohms.
3.
Measure the heater relay Ohms.
Programmer fault
Programmer fault
Programmer fault
Programmer fault
Programmer fault
The washing program has been interrupted. Check
the fuses.
Water inlet fault
ater inlet fault
ater inlet fault
ater inlet fault
ater inlet fault
Indicates a fault in the water supply.
1.
Make sure the water supply to the machine has
been turned on (cold fill only)
2.
Check that the filter in the machine water inlet
is not blocked.
Draining fault
Draining fault
Draining fault
Draining fault
Draining fault
Draining has taken too long. Check the drain hose
and the drain pump as follows:
1.
Make sure an object is not stuck in the drain
hose outlet. Clean out the hose.
2.
Make sure the drain pump isn
’
t blocked by
foreign objects. Clean out the pump.
3.
Make sure the drain hose isn
’
t kinked.
4.
After solving the problem, run program 10
(Drain).
Position S
osition S
osition S
osition S
osition S
If the program knob stops in position
“
S
”
after the
program has finished or been interrupted, this
indicates that a motor fault, a level sensor fault, or a
program fault has occurred during the program
cycle.
W600 AND W620 TEST PROGRAM AND FAULT INDICATIONS