Asus P I-XP6NP5 User Manual - Page 27

IDE Activity LED JP15

Get Asus P I-XP6NP5 PDF manuals and user guides View all Asus P I-XP6NP5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

III. INSTALLATION 7. Primary / Secondary IDE connectors (Two 40-pin Block) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" & "Boot Sequence" in the BIOS Features Setup of the BIOS SOFTWARE) (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). TIP: You may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup. Pin 1 Primary IDE Connector Secondary IDE Connector 8. IDE Activity LED (JP15) This connector connects to the IDE (hard disk) activity indicator light on the system cabinet. III. INSTALLATION (Connectors) + JP15 IDE Activity LED ASUS P/I-XP6NP5 User's Manual 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS P/I-XP6NP5 User’s Manual
21
III. INSTALLATION
(Connectors)
III.
INSTALLATION
7.
Primary / Secondary IDE connectors
(Two 40-pin Block)
These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s).
If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly.
Please refer to the
documentation of your hard disk for the jumper settings.
BIOS now supports
SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" &
"Boot Sequence" in the BIOS Features Setup of the BIOS SOFTWARE)
(Pin
20 is removed to prevent inserting in the wrong orientation when using
ribbon cables with pin 20 plugged).
TIP:
You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector.
You may install one operating system on an IDE drive and
another on a SCSI drive and select the boot disk through BIOS Features Setup.
Primary IDE Connector
Pin 1
Secondary IDE Connector
8.
IDE Activity LED (JP15)
This connector connects to the IDE (hard disk) activity indicator light on the
system cabinet.
IDE Activity LED
JP15
+