Asus P2E-VM P2E-VM User Manual - Page 31

Wake On LAN Connector 3-pin WOL_CON

Get Asus P2E-VM PDF manuals and user guides View all Asus P2E-VM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

III. INSTALLATION Connectors III. INSTALLATION 14. IrDA / Fast IR-Compliant infrared module connector (5-pin IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through "UART2 Use Infrared" in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown on the Back View and connect a ribbon cable from the module to the motherboard according to the pin definitions. R +5V IRRX IRTX (NC) GND Front View Back View IRTX GND IRRX +5V (NC) P2L-VM/P2E-VM Infrared Module Connector 15. Wake On LAN Connector (3-pin WOL_CON) These connector connects to LAN cards with a Wake On LAN output, such as the ASUS PCI-L101 (see ASUS LAN Card section). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that the WAKE On LAN Power Up Control is set to Enabled (see "Power Management Setup" under BIOS SOFTWARE section) and that your system has an ATX power supply with at least 720mA +5V standby power. R +5 Volt Standby PME Ground IMPORTANT: Requires an ATX power supply with at least 720mA +5-volt standby power P2L-VM/P2E-VM Wake on LAN Connector ASUS P2L-VM/P2E-VM User's Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
ASUS P2L-VM/P2E-VM User’s Manual
31
III. INSTALLATION
Connectors
III.
INSTALLATION
14. IrDA / Fast IR-Compliant infrared module connector (5-pin IR)
This connector supports the optional wireless transmitting and receiving infrared
module.
This module mounts to a small opening on system cases that support this
feature.
You must also configure the setting through “UART2 Use Infrared” in
Chipset Features Setup
to select whether UART2 is directed for use with COM2
or IrDA.
Use the five pins as shown on the Back View and connect a ribbon cable
from the module to the motherboard according to the pin definitions.
P2L-VM/P2E-VM Infrared Module Connector
Front View
+5V
IRTX
IRRX
(NC)
GND
Back View
+5V
IRRX IRTX
(NC)
GND
15. Wake On LAN Connector (3-pin WOL_CON)
These connector connects to LAN cards with a Wake On LAN output, such as
the ASUS PCI-L101 (see
ASUS LAN Card
section). The connector powers up
the system when a wakeup packet or signal is received through the LAN card.
IMPORTANT:
This feature requires that the
WAKE On LAN
Power Up Con-
trol
is set to
Enabled
(see “Power Management Setup” under
BIOS SOFT-
WARE
section
)
and that your system has an ATX power supply with at least
720mA +5V standby power.
P2L-VM/P2E-VM Wake on LAN Connector
IMPORTANT:
Requires an ATX power
supply with at least 720mA +5-volt
standby power
+5 Volt Standby
PME
Ground