Asus P2V-B P2V-B User Manual - Page 30

SCSI device or IDE CD-ROM bootup see HDD Sequence SCSI/IDE First &amp

Get Asus P2V-B PDF manuals and user guides View all Asus P2V-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

III. HARDWARE SETUP 5. Primary / Secondary IDE Connectors (Two 40-1 pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" & "Boot Sequence" in BIOS Features Setup of BIOS SETUP) (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). TIP: You may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. You may install up to four operating systems on each IDE drive and select the boot disk through "Boot Sequence" in BIOS Features Setup. NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1 Secondary IDE Connector P2V-B R PIN 1 Primary IDE Connector P2V-B Primary / Secondary IDE Connectors 6. IDE Activity LED Connector (2-pin IDELED) This connector supplies power to the cabinet's IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. III. H/W SETUP Connectors TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. P2V-B R IDELED P2V-B IDE Activity LED Connector 30 ASUS P2V-B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
30
ASUS P2V-B User’s Manual
III. HARDWARE SETUP
5.
Primary / Secondary IDE Connectors
(Two 40-1 pin IDE)
These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s).
If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly.
Please refer to the
documentation of your hard disk for the jumper settings.
BIOS now supports
SCSI device or IDE CD-ROM bootup (see “HDD Sequence SCSI/IDE First” &
“Boot Sequence” in
BIOS Features Setup
of BIOS SETUP)
(Pin 20 is removed
to prevent inserting in the wrong orientation when using ribbon cables with
pin 20 plugged).
TIP:
You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector.
You may install up to four operating systems on each IDE drive
and select the boot disk through “Boot Sequence” in
BIOS Features Setup
.
P2V-B Primary / Secondary IDE Connectors
NOTE:
Orient the red markings (usually zigzag)
on the IDE ribbon cable to PIN 1
Primary IDE Connector
Secondary IDE Connector
PIN 1
P2V-B
6.
IDE Activity LED Connector (2-pin IDELED)
This connector supplies power to the cabinet’s IDE activity LED.
Read and
write activity by devices connected to the Primary or Secondary IDE connectors
will cause the LED to light up.
P2V-B IDE Activity LED Connector
TIP:
If the case-mounted LED does not light,
try reversing the 2-pin plug.
IDELED
P2V-B
Connectors
III.
H/W SETUP