Asus P2V-B P2V-B User Manual - Page 32

ATX Power Switch/Soft Power Switch Lead 2-pin PWR.SW

Get Asus P2V-B PDF manuals and user guides View all Asus P2V-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

III. HARDWARE SETUP 9. Message LED Lead (2-pin MSG.LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or messages waiting in the inbox. This function requires ACPI OS support. 10. System Management Interrupt Lead (2-pin SMI) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). If you want to use this connector, "Suspend Switch" in Power Management Setup of BIOS SETUP section should be on the default setting of Enable. 11. ATX Power Switch/Soft Power Switch Lead (2-pin PWR.SW) The system power can be controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 12. Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. 13. System Power LED Lead (3-1 pin PWR.LED) This 3-pin connector connects the system power LED, which lights when the system is powered on and flashes when it is in sleep mode. 14. Keyboard Lock Switch Lead (2-pin KEYLOCK) This 2-pin connector connects to the case-mounted key switch to allow keyboard locking. 15. System Warning Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker. III. H/W SETUP Connectors *Requires an ATX power supply, optional ATX to AT AT power connector adapter and a momentary switch. P2V-B R System GND Speaker GND Keyboard Lock GND Power LED Reset Switch Power Switch* SMI Switch Message LED P2V-B System Panel Connectors 32 ASUS P2V-B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
32
ASUS P2V-B User’s Manual
III. HARDWARE SETUP
9.
Message LED Lead (2-pin MSG.LED)
This indicates whether a message has been received from a fax/modem. The
LED will remain lit when there is no signal and blink when there is data transfer
or messages waiting in the inbox.
This function requires ACPI OS support.
10. System Management Interrupt Lead (2-pin SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the “Turbo Switch”
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
If you want to use this connector,
“Suspend Switch” in
Power Management Setup
of BIOS SETUP section should
be on the default setting of
Enable.
11.
ATX Power Switch/Soft Power Switch Lead (2-pin PWR.SW)
The system power can be controlled by a momentary switch connected to this
lead.
Pushing the button once will switch the system between ON and SLEEP.
Pushing the switch while in the ON mode for more than 4 seconds will turn the
system off.
The system power LED shows the status of the system’s power.
12. Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system’s power supply.
13. System Power LED Lead (3-1 pin PWR.LED)
This 3-pin connector connects the system power LED, which lights when the
system is powered on and flashes when it is in sleep mode.
14. Keyboard Lock Switch Lead (2-pin KEYLOCK)
This 2-pin connector connects to the case-mounted key switch to allow key-
board locking.
15. System Warning Speaker Connector (4-pin SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
P2V-B System Panel Connectors
Reset Switch
Power Switch*
GND
GND
System
Speaker
GND
Keyboard Lock
Message LED
SMI Switch
Power LED
*Requires an ATX power supply, optional ATX to AT
AT power connector adapter and a momentary switch.
P2V-B
Connectors
III.
H/W SETUP