Behringer CRAVE Quick Start Guide - Page 21
CRAVE Sequencer operation, CRAVE Tempo and Assign Mode Select
View all Behringer CRAVE manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
40 CRAVE CRAVE Sequencer operation (EN) Step 4: Sequencer operation CREATING A PATTERN IN STEP MODE 1. Press SHIFT and STEP> to select the Sequencer's STEP mode. The flashing LOCATION LED will turn from green (Keyboard mode) to yellow (Step mode). 2. Initialise the current pattern by pressing SHIFT, RESET, and PATTERN at the same time. This will delete any previous steps of the current pattern. (If you want to use the current pattern instead, then do not initialise it.) 3. Press PAGE to move to a desired page of your pattern. Then press SET END and a STEP switch to choose the length of the pattern. For example, if you are on page 1 and press SET END + 8, then the pattern length is 8 steps. If you press PAGE and reach page 4, and press SET END + 8, then the pattern will be 32 steps long (4 pages of 8 steps each). 4. When the desired SET END is selected, all the STEP switch LEDs up to that step will be on solid red. 5. Press SHIFT and any one of the STEP switches at the same time. It will begin to flash, indicating it is the current step about to be edited. You can now add a note, or a rest, or any of the other functions described above in the Keyboard mode, such as Ratchet, Glide, Accent, change gate length and so on. 6. Press SHIFT and the current STEP switch to finish editing that step. It will stop flashing. 7. Repeat procedure steps 5 and 6 above, until all your required steps are good. 8. Press PLAY/STOP to play the pattern. 9. While playing, you can add temporary adjustments as shown in the "LIVE PERFORMANCE" procedure above. SAVING A PATTERN IN STEP MODE Save the pattern using the "SAVING A PATTERN" procedure shown above for the KEYBOARD mode. Caution: Do not turn off the unit, or create a new pattern, or the current unsaved pattern will be lost. Quick Start Guide 41 CRAVE Tempo and Assign Mode Select (EN) Step 5: Tempo and Assign Mode Select The tempo input and assign mode may be changed using the following procedure: 1. Press SHIFT+ HOLD/REST + 8 to enter the setting mode. The LOCATION LED 1 will blink yellow. 2. Press to select pages 1 or 2. The yellow LOCATION LED shows the current page: 3. Page 1 allows you to select the tempo input mode, 1 to 3. (Please see Programming Tempo Input Modes, below) 4. Page 2 allows you to select the assign output mode, 1 to 16. (Please see Assignable Output Mode, below) 5. Press STEP switches 1 to 8 to select numeric values from 1 to 8. The current value is indicated by a green LOCATION LED. 6. To access values 9 to 16, press SHIFT + STEP switch 1 to 8. The current value is shown by a red LOCATION LED. 7. Note: If a setting is on the same LED number as the current page LED, then the LED will flash alternately between the yellow page color and the green or red parameter color. 8. Press SHIFT + HOLD/REST + 8 to exit the setting mode, and save any parameter changes. Programming Tempo Input Modes: 1. TEMPO CV INPUT MODE 2. TEMPO SINGLE CLOCK ADVANCE MODE 3. TEMPO DIN SYNC MODE Assignable Output Modes: 1. Accent 2. Sequencer Clock 3. Sequencer Clock/2 4. Sequencer Clock/4 5. Sequencer Step Ramp 6. Sequencer Step Saw 7. Sequencer Step Triangle 8. Sequencer Step Random 9. Sequencer Step 1 Trigger Output 10. MIDI Velocity 11. MIDI Channel Pressure 12. MIDI Pitch Bend 13. MIDI CC1 14. MIDI CC2 15. MIDI CC4 16. MIDI CC7