Beko WMI71641 User Manual - Page 27

Draining any remaining water, and cleaning the pump filter - clean filter

Page 27 highlights

A There may be water at 90°C in the machine. the filter must be cleaned only after the inside water is cooled down to avoid hazard of scalding. 2- Open the filter cap. The filter cap may be composed of one or two pieces according to the model of your machine. If it is composed of two pieces, press the tab on the filter cap downwards and pull • Close the taps. the piece out towards yourself. C If your machine is built-in, then it does not contain a filter cover. • Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush. • If the filters are very dirty, you can pull them out by means of pliers and clean them. • Take out the filters on the flat ends of the water intake hoses together with If it is composed of one piece, hold it from the gaskets and clean thoroughly under streaming water. both sides and open it by pulling out. C You can remove the filter cover • Replace the gaskets and filters by slightly pushing the kick plate carefully to their places and tighten the downwards with a screwdriver, hose nuts by hand. through the gap above the filter cover. Draining any remaining water and cleaning the pump filter Filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump propeller during discharging of the washing water. Thus, a good water discharge is achieved and the pump life is extended. • If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter. In addition, water may have to be drained off completely in the following cases: • before transporting the machine (e.g. when moving house) • when there is the danger of frost In order to clean the dirty filter and discharge the water; 1- Unplug the machine to cut off the supply power. 3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item. If your product is supplied with an emergency drain hose, do the following as shown in the figure below: 27 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

EN
27
Close the taps.
Remove the nuts of the water intake
hoses to clean the surfaces of the
filters on the water intake valves with
an appropriate brush.
If the filters are very dirty, you can pull
them out by means of pliers and clean
them.
Take out the filters on the flat ends of
the water intake hoses together with
the gaskets and clean thoroughly
under streaming water.
Replace the gaskets and filters
carefully to their places and tighten the
hose nuts by hand.
Draining any remaining water
and cleaning the pump filter
Filter system in your machine prevents
solid items such as buttons, coins and
fabric fibers clogging the pump propeller
during discharging of the washing water.
Thus, a good water discharge is achieved
and the pump life is extended.
If your machine fails to drain the water,
the pump filter may be clogged. You
may have to clean it every 2 years or
whenever it is plugged. Water must be
drained off to clean the pump filter.
In addition, water may have to be drained
off completely in the following cases:
before transporting the machine (e.g.
when moving house)
when there is the danger of frost
In order to clean the dirty filter and
discharge the water;
1- Unplug the machine to cut off the
supply power.
A
There may be water at 90°C in the
machine. the filter must be cleaned
only after the inside water is cooled
down to avoid hazard of scalding.
2- Open the filter cap. The filter cap
may be composed of one or two pieces
according to the model of your machine.
If it is composed of two pieces, press the
tab on the filter cap downwards and pull
the piece out towards yourself.
C
If your machine is built-in, then it does
not contain a filter cover.
If it is composed of one piece, hold it from
both sides and open it by pulling out.
C
You can remove the filter cover
by slightly pushing the kick plate
downwards with a screwdriver,
through the gap above the filter cover.
3- An emergency drain hose is supplied
with some of our models. Others are not
supplied with this item.
If your product is supplied with an
emergency drain hose, do the following as
shown in the figure below: