Beko WMI71641 User Manual - Page 30

Run either the Pump or Spin Programme.

Get Beko WMI71641 PDF manuals and user guides View all Beko WMI71641 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

The door is jammed. - Water level might be above the lower level of the door. - Machine might be heating up the water or it may be at the spinning cycle. - Due to an electrical mechanism, the door can only be opened a few minutes after the Programme has stopped. - Run either the "Pump" or "Spin" Programme. - Wait until the process is over. - Wait until the process is over. Machine fills with water when a process is cancelled. Inside of machine may be hot. For safety reasons cold water is added to cool the hot wash load It continuously spins. Remaining time does not count down. (On models with display) There may be an imbalance of laundry in the machine. - The automatic spin correction system might have been activated due to the unbalanced distribution of the laundry in the drum. - The laundry in the drum may be clustered (bundled laundry in a bag). Laundry should be rearranged and re-spun. - No spinning is performed when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its environment. Washing time takes longer than the time specified in the manual - Water pressure may be low. - Supply voltage may be low. - Input temperature of water may be low. - There may be an imbalance of laundry in the machine. - Number of rinses and/or amount of rinse water might have increased. - The machine will wait until there is sufficient amount of water, which will lengthen the washing time to avoid poor washing results due to insufficient water. - Washing time is extended to avoid poor washing results when the supply voltage is low. - Cycle time is extended to heat up the water when the input water is cold. Also, washing time can be lengthened to avoid poor washing results. - The automatic spin correction system might have been activated due to the unbalanced distribution of the laundry in the drum. - The laundry in the drum may be clustered (bundled laundry in a bag). - Laundry should be rearranged and re-spun. - No spinning is performed when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its environment. - Water amount is increased to obtain a better rinse and a rinse cycle is added when necessary. 30 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
EN
30
The door is jammed.
- Water level might be above the lower
level of the door.
- Machine might be heating up the water
or it may be at the spinning cycle.
- Due to an electrical mechanism, the door
can only be opened a few minutes after
the Programme has stopped.
- Run either the “Pump” or “Spin” Programme.
- Wait until the process is over.
- Wait until the process is over.
Machine fills with water when a process is cancelled.
Inside of machine may be hot.
For safety reasons cold water is added to cool the
hot wash load
It continuously spins. Remaining time does not count down. (On models with display)
There may be an imbalance of laundry in
the machine.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Washing time takes longer than the time specified in the manual
- Water pressure may be low.
- Supply voltage may be low.
- Input temperature of water may be low.
- There may be an imbalance of laundry in
the machine.
- Number of rinses and/or amount of rinse
water might have increased.
- The machine will wait until there is sufficient
amount of water, which will lengthen the washing
time to avoid poor washing results due to
insufficient water.
- Washing time is extended to avoid poor washing
results when the supply voltage is low.
- Cycle time is extended to heat up the water when
the input water is cold. Also, washing time can be
lengthened to avoid poor washing results.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- The laundry in the drum may be clustered
(bundled laundry in a bag).
- Laundry should be rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Water amount is increased to obtain a better rinse
and a rinse cycle is added when necessary.