Bosch B18IF800SP Installation Instructions - Page 15

Aligning the appliance in the installation niche, Depth alignment

Get Bosch B18IF800SP PDF manuals and user guides View all Bosch B18IF800SP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

2. Aligning the appliance in the installation niche Note: To ensure that the appliance functions correctly, it must be set perfectly levelled. Depth alignment The positioning aid on the door have been designed for the following total thickness of door panels: ■ 3/4" (19 mm) ■ 1 1/2" (38 mm) Always take account of the possible differing thickness of the panel fronts which are to be fitted subsequently. 1. Align the appliance with the cabinet fronts using the positioning aid. Place level over the positioning aid on the door. en-us The mark (a) attached at the appliance base is used as a standard gage for height adjustment. When adjusting the height, align this mark at a height of 1 1/4" (32 mm) above the floor. It is very important to comply with this dimension for the subsequent alignment of the furniture fronts. The height adjustment gauge (b) is used to set this height correctly. The upper edge of the gauge must be in alignment with the mark on the appliance. 2. Unscrew the feet at the front of the appliance until the mark (a) on the appliance is in alignment with the upper edge of the height adjustment gauge (b). 3. Align the appliance vertically using the feet at the back. Use a level! Height alignment Note: ■ Do not twist or jam the appliance inside the installation niche! When adjusting the heightadjustable feet, proceed gradually: Always alternate between left and right, etc. ■ For easier adjustment of the rear feet take the weight off by slightly tilting the appliance forward. ■ When using a wooden beam as an alternative antitip mechanism, turn the appliance as far as it will go against the wooden beam. Do not bend against the wooden beam. The height-adjustable feet at the front and rear can all be adjusted from the front. Front: Rear: with open-ended wrench 1/2" (Width across flats 13 mm) with 5/16" (8 mm) hex nut driver via flexible shaft. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
en-us
15
2.
Aligning the appliance in the
installation niche
Note:
To ensure that the appliance functions correctly, it must
be set perfectly levelled.
Depth alignment
The positioning aid on the door have been designed for
the following total thickness of door panels:
■
3
/
4
" (19 mm)
■
1
1
/
2
" (38 mm)
Always take account of the possible differing thickness
of the panel fronts which are to be fitted subsequently.
1.
Align the appliance with the cabinet fronts using
the positioning aid.
Place level over the positioning aid on the door.
Height alignment
Note:
■
Do not twist or jam the appliance inside the
installation niche! When adjusting the
heightadjustable feet, proceed gradually: Always
alternate between left and right, etc.
■
For easier adjustment of the rear feet take the
weight off by slightly tilting the appliance forward.
■
When using a wooden beam as an alternative
antitip mechanism, turn the appliance as far as it
will go against the wooden beam. Do not bend
against the wooden beam.
The height-adjustable feet at the front and rear can all
be adjusted from the front.
The mark (
a
) attached at the appliance base is used as
a standard gage for height adjustment. When adjusting
the height, align this mark at a height of 1
1
/
4
" (32 mm)
above the floor.
It is very important to comply with this dimension for the
subsequent alignment of the furniture fronts.
The height adjustment gauge (
b
) is used
to set this height correctly. The upper
edge of the gauge must be in alignment
with the mark on the appliance.
2.
Unscrew the feet at the front of the appliance until
the mark (
a
) on the appliance is in alignment with
the upper edge of the height adjustment
gauge (
b
).
3.
Align the appliance vertically using the feet at the
back. Use a level!
Front:
with open-ended wrench
1
/
2
"
(Width across flats 13 mm)
Rear:
with
5
/
16
" (8 mm) hex nut driver via
flexible shaft.