Bosch NWD-455V03-20P Operating Instructions - Page 23

Attach the mounting plate, Make the connections

Get Bosch NWD-455V03-20P PDF manuals and user guides View all Bosch NWD-455V03-20P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

FlexiDome IP Mounting the unit | en 23 3.1 Attach the mounting plate 1. Use the mounting plate as a drilling template to drill three holes in the mounting surface. 2. Use the supplied plugs and screws to attach the mounting plate to the surface. 3. With a rear connection, leave the cap in place. With a side connection: a. remove the cap covering the side entrance; b. attach a 22 mm / ½ inch (PG16) gland conduit to the mounting plate. 3.2 Make the connections To connect the wiring to the camera, use the metal mounting wire to hold the camera during installation on a ceiling. Make the power and network connection from inside the connection box. Suspension wire Connection box Fig. 3.3 Preparation 1. Pull out the connection box from the camera encasing. 2. To open the connection box, loosen the Phillips screws, and open the cover flips. CAUTION! ! Never supply power via the Ethernet connection (PoE) when power is supplied via the power connector. Bosch Security Systems Operating Instructions V 1.0 | 2006.12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
FlexiDome IP
Mounting the unit | en
23
Bosch Security Systems
Operating Instructions
V 1.0 | 2006.12
3.1
Attach the mounting plate
1.
Use the mounting plate as a drilling template to drill three
holes in the mounting surface.
2.
Use the supplied plugs and screws to attach the mounting
plate to the surface.
3.
With a rear connection, leave the cap in place. With a side
connection:
a.
remove the cap covering the side entrance;
b.
attach a 22 mm / ½ inch (PG16) gland conduit to the
mounting plate.
3.2
Make the connections
To connect the wiring to the camera, use the metal mounting
wire to hold the camera during installation on a ceiling. Make
the power and network connection from inside the connection
box.
Fig. 3.3
Preparation
1.
Pull out the connection box from the camera encasing.
2.
To open the connection box, loosen the Phillips screws,
and open the cover flips.
Suspension wire
Connection box
!
CAUTION!
Never supply power via the Ethernet connection (PoE) when
power is supplied via the power connector.