Brother International FAX-8650P Service Manual - Page 66

Laser Unit and Toner Sensor PCB, Reassembling Notes, Do not disturb it.

Get Brother International FAX-8650P - B/W Laser - Fax PDF manuals and user guides View all Brother International FAX-8650P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

1.11 Laser Unit and Toner Sensor PCB (1) Remove the screw (Taptite, cup B M3x8) from the toner sensor PCB. (2) Slightly lift up the toner sensor PCB and disconnect its harness. (3) Remove the three screws from the laser unit. (4) Slightly lift up the laser unit and disconnect the following from the main PCB: - Laser diode harness (5-pin) - Toner sensor harness (4-pin) if the toner sensor PCB is installed - Polygon motor flat cable NOTE: When handling the laser unit, take care not to touch the inside of the unit, glass, or mirror. NOTE: On the small PCB at the right side of the laser unit is a 2-pin connector which is for the adjustment in the factory. Do not disturb it. n Reassembling Notes • Before putting the laser unit back into place, check for any toner particles, paper dust or dirt, and clean them out. • When installing the laser unit, make sure that the laser diode harness, toner sensor harness and polygon motor flat cable are routed as shown above. • Make sure that the sponge is placed below the laser unit. IV - 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
IV
- 28
1.11
Laser Unit and Toner Sensor PCB
(1)
Remove the screw (Taptite, cup B M3x8) from the toner sensor PCB.
(2)
Slightly lift up the toner sensor PCB and disconnect its harness.
(3)
Remove the three screws from the laser unit.
(4)
Slightly lift up the laser unit and disconnect the following from the main PCB:
- Laser diode harness (5-pin)
- Toner sensor harness (4-pin) if the toner sensor PCB is installed
- Polygon motor flat cable
NOTE:
When handling the laser unit, take care not to touch the inside of the unit, glass, or
mirror.
NOTE:
On the small PCB at the right side of the laser unit is a 2-pin connector which is for
the adjustment in the factory.
Do not disturb it.
n
Reassembling Notes
•
Before putting the laser unit back into place, check for any toner particles, paper dust or dirt,
and clean them out.
•
When installing the laser unit, make sure that the laser diode harness, toner sensor harness
and polygon motor flat cable are routed as shown above.
•
Make sure that the sponge is placed below the laser unit.