Brother International HL 1270N Users Manual - English - Page 42

Test Print Mode, Test Sample - problem

Get Brother International HL 1270N - B/W Laser Printer PDF manuals and user guides
UPC - 012502526001
View all Brother International HL 1270N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Test Print Mode The printer has the following test print modes. Follow these steps:  1. Make sure that the front cover is closed.  2. Hold down the control panel button and turn on the power switch. Keep the button depressed until the Drum LED comes on. The Drum LED illuminates to indicate that the printer is in the test print mode.  3. Release the button and then press it again to execute the test print, or hold down the button to select another option as shown in the table below and then release the button and press it again to execute the selected option. LED Lit Drum Ready Alarm Data Choice Test Sample Page Print Config & Print Fonts I Factory Reset Hex Dump Print Function The printer prints a test sample page. The printer returns to the Ready status after printing. The printer prints the current configuration of the printer and a list of the internal fonts. The printer returns to the Ready status after printing. The printer is restored to the factory setting and permanent fonts and macros are cleared. The printer returns to the Ready status after printing. The printer can print data as hexadecimal values so that you can check data errors and problems. To exit from this mode, you must turn off the printer. 1-34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
1-34
Test Print Mode
The printer has the following test print modes. Follow these steps:
1.
Make sure that the front cover is closed.
2.
Hold down the control panel button and turn on the power switch.
Keep the button depressed
until the
Drum
LED comes on.
The
Drum
LED illuminates to indicate that the printer is in the test print mode.
3.
Release the button and then press it again to execute the test print, or hold down the button to
select another option as shown in the table below and then release the button and press it again
to execute the selected option.
LED Lit
Choice
Function
Drum
Test Sample Page
The printer prints a test sample page.
The printer returns to the Ready status after
printing.
Ready
Print Config
&
Print Fonts I
The printer prints the current configuration
of the printer and a list of the internal fonts.
The printer returns to the Ready status after
printing.
Alarm
Factory Reset
The printer is restored to the factory setting
and permanent fonts and macros are
cleared.
The printer returns to the Ready status after
printing.
Data
Hex Dump Print
The printer can print data as hexadecimal
values so that you can check data errors and
problems.
To exit from this mode, you
must turn off the printer.