Canon DR-2080C Startup Guide - Page 28

You can set the SCSI ID by using the DIP-switch provided on the left side

Get Canon DR-2080C - Document Scanner PDF manuals and user guides View all Canon DR-2080C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Notice ● Make sure that the scanner and your PC are both turned off when connecting the scanner to the PC. ● Since the provided SCSI board uses a D-sub 25-pin connector, take care to connect the SCSI cable to the SCSI board connector, and not to the D-sub 25-pin connector of the printer port. ● The terminator of the scanner is set to ON as default. Be sure to turn off all terminators of the SCSI devices connected between the scanner and the PC. Note The SCSI ID is set to "2" at the factory before shipping. You can set the SCSI ID by using the DIP-switch provided on the left side of the scanner. In the DIP-switch settings, the SCSI ID can be set to ON by turning the switch to the rear side, or OFF by turning it to the front side. SCSI ID switches ON 1 2 Default settings (SCSI ID = 2) Refer to the following table when setting the SCSI ID. If there are other SCSI devices connected to or inside the PC, make sure to set a unique ID for the scanner. SCSI ID 2 3 4 5 SW1 OFF ON OFF ON SW2 OFF OFF ON ON 26 Installing the Scanner

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
26
Installing the Scanner
Notice
●
Make sure that the scanner and your PC are both turned off when
connecting the scanner to the PC.
●
Since the provided SCSI board uses a D-sub 25-pin connector, take care to
connect the SCSI cable to the SCSI board connector, and not to the D-sub
25-pin connector of the printer port.
●
The terminator of the scanner is set to ON as default. Be sure to turn off all
terminators of the SCSI devices connected between the scanner and the PC.
Note
The SCSI ID is set to “2” at the factory before shipping.
You can set the SCSI ID by using the DIP-switch provided on the left side of
the scanner. In the DIP-switch settings, the SCSI ID can be set to ON by
turning the switch to the rear side, or OFF by turning it to the front side.
1
ON
2
SCSI ID switches
Default settings
(SCSI ID = 2)
Refer to the following table when setting the SCSI ID. If there are other SCSI
devices connected to or inside the PC, make sure to set a unique ID for the
scanner.
SCSI ID
SW1
SW2
2
OFF
OFF
3
ON
OFF
4
OFF
ON
5
ON
ON