Canon LV-X300 User Manual - Page 35

Magnifying and searching for details, Selecting the aspect ratio, D.ZOOM, AUTO PC, DISPLAY, OK/IMAGE

Get Canon LV-X300 PDF manuals and user guides View all Canon LV-X300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

ENGLISH Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press D.ZOOM +/- to display the Zoom bar. 2. Press D.ZOOM + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4. To restore the picture to its original size, press AUTO PC. You can also press D.ZOOM -. When the key is pressed again, the picture is further reduced until it is restored to the original size. • Using the OSD menu 1. Press MENU and then press / until the DISPLAY menu is highlighted. 2. Press to highlight D.ZOOM and press OK/IMAGE. The Zoom bar is displayed. 3. Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps. 4. Press on the projector repeatedly to magnify the picture to a desired size. 5. To navigate the picture, press OK/IMAGE to switch to the panning mode and press the directional arrows ( , , , ) to navigate the picture. 6. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 7. To reduce size of the picture, press OK/IMAGE to switch back to the zoom in/out functionality, and press AUTO PC to restore the picture to its original size. You can also press repeatedly until it is restored to the original size. The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details. Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): 1. Press MENU and then press / until the DISPLAY menu is highlighted. 2. Press to highlight Aspect. 3. Press / to select an aspect ratio to suit the format of the video signal and your display requirements. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
35
ENGLISH
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys
for navigating the picture.
•
Using the remote control
1.
Press
D.ZOOM +/-
to display the Zoom bar.
2.
Press
D.ZOOM +
to magnify the center of the picture. Press the
key repeatedly until the picture size is suitable for your need.
3.
Use the directional arrows (
,
,
,
) on the projector or
remote control to navigate the picture.
4.
To restore the picture to its original size, press
AUTO PC
. You
can also press
D.ZOOM -
. When the key is pressed again, the
picture is further reduced until it is restored to the original size.
•
Using the OSD menu
1.
Press
MENU
and then press
/
until the
DISPLAY
menu is highlighted.
2.
Press
to highlight
D.ZOOM
and press
OK/IMAGE
. The Zoom bar is displayed.
3.
Repeat steps 2-4 in the section of
"Using the remote control"
above. Or if you are using the projector
control panel, continue to the following steps.
4.
Press
on the projector repeatedly to magnify the picture to a desired size.
5.
To navigate the picture, press
OK/IMAGE
to switch to the panning mode and press the directional
arrows (
,
,
,
) to navigate the picture.
6.
Use the directional arrows (
,
,
,
) on the projector or remote control to navigate the picture.
7.
To reduce size of the picture, press
OK/IMAGE
to switch back to the zoom in/out functionality, and
press
AUTO PC
to restore the picture to its original size. You can also press
repeatedly until it is
restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the picture
while searching for details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in
4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can dynamically
stretch and scale the image output to a different aspect than that of the image input signal.
To change the projected image ratio (no matter what aspect the source is):
1.
Press
MENU
and then press
/
until the
DISPLAY
menu is highlighted.
2.
Press
to highlight
Aspect
.
3.
Press
/
to select an aspect ratio to suit the format of the video signal and your display
requirements.