Canon ZR 800 ZR800 Instruction Manual - Page 49

List of Messages, Additional Information - support

Get Canon ZR 800 - Camcorder - 680 KP PDF manuals and user guides
UPC - 013803078190
View all Canon ZR 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Trouble? 49 Problem Solution No sound from the built-in Open the LCD panel. - speaker. Speaker volume is turned off. Adjust the volume with the 25 [SPEAKER VOLUME] setting. Image will not appear on the TV screen. Check again that the camcorder is properly connected to the TV. 42 Tape is running, but image will TV/VIDEO selector on the TV is not set to VIDEO. Set the 43 not appear on the TV screen. selector to VIDEO. Video heads are dirty. Clean the video heads. 2 You attempted to play back or dub copyright a protected tape. 44 Stop playback/dubbing. Editing Problem Solution Cannot record with this Wrong signal standard. Refer also to the instruction manual of - camcorder video input from an the connected device. external video device connected using a DV cable. Additional Information List of Messages Message Explanation/Solution SET THE TIME ZONE, You have not set the time zone, date and time. This message 21 DATE AND TIME appears each time you turn the power on until you set the time zone, date and time. CHANGE THE BATTERY Battery pack is exhausted. Replace or charge the battery pack. 15 PACK THE TAPE IS SET FOR Cassette is protected. Replace the cassette or change the position 52 ERASURE PREVENTION of the protect switch. REMOVE THE CASSETTE Camcorder stopped operating to protect the tape. Remove the 17 cassette and reinsert it. CHECK THE INPUT The DV cable is not correctly connected to the DV terminal, or the 42 connected digital device is turned off. The video input signal is in a different television system (PAL or - SECAM). CONDENSATION HAS Condensation has been detected in the camcorder. 54 BEEN DETECTED CONDENSATION HAS Condensation has been detected in the camcorder. Remove the 54 BEEN DETECTED cassette. REMOVE THE CASSETTE TAPE END Tape reached the end. Rewind the tape or replace the cassette. - INCORRECT TAPE SPECIFICATION You attempted to play back a tape recorded in a different television - system (PAL or SECAM) or in a recording standard not supported by this camcorder.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Trouble?
49
Additional Information
Editing
List of Messages
No sound from the built-in
speaker.
Open the LCD panel.
–
Speaker volume is turned off. Adjust the volume with the
[SPEAKER VOLUME] setting.
25
Image will not appear on the
TV screen.
Check again that the camcorder is properly connected to the TV.
42
Tape is running, but image will
not appear on the TV screen.
TV/VIDEO selector on the TV is not set to VIDEO. Set the
selector to VIDEO.
43
Video heads are dirty. Clean the video heads.
2
You attempted to play back or dub copyright a protected tape.
Stop playback/dubbing.
44
Problem
Solution
Cannot record with this
camcorder video input from an
external video device
connected using a DV cable.
Wrong signal standard. Refer also to the instruction manual of
the connected device.
–
Message
Explanation/Solution
SET THE TIME ZONE,
DATE AND TIME
You have not set the time zone, date and time. This message
appears each time you turn the power on until you set the time
zone, date and time.
21
CHANGE THE BATTERY
PACK
Battery pack is exhausted. Replace or charge the battery pack.
15
THE TAPE IS SET FOR
ERASURE PREVENTION
Cassette is protected. Replace the cassette or change the position
of the protect switch.
52
REMOVE THE CASSETTE
Camcorder stopped operating to protect the tape. Remove the
cassette and reinsert it.
17
CHECK THE INPUT
The DV cable is not correctly connected to the DV terminal, or the
connected digital device is turned off.
42
The video input signal is in a different television system (PAL or
SECAM).
–
CONDENSATION HAS
BEEN DETECTED
Condensation has been detected in the camcorder.
54
CONDENSATION HAS
BEEN DETECTED
REMOVE THE CASSETTE
Condensation has been detected in the camcorder. Remove the
cassette.
54
TAPE END
Tape reached the end. Rewind the tape or replace the cassette.
–
INCORRECT TAPE
SPECIFICATION
You attempted to play back a tape recorded in a different television
system (PAL or SECAM) or in a recording standard not supported
by this camcorder.
–
Problem
Solution