Home » Cisco Manuals » Bridges & Routers » Cisco SR224T-NA » Manual Viewer

Cisco SR224T-NA Administration Guide - Page 74

Available Optional TLVs, Selected Optional TLVs, Advertisement Mode, Port Description, System Name

Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Configuring Discovery Configuring LLDP 8 • Available Optional TLVs-Select the information to be published by the switch by moving the TLV to the Selected Optional TLVs list. The available TLVs contain the following information: - Port Description-Information about the port, including manufacturer, product name and hardware/software version. - System Name-System's assigned name (in alpha-numeric format). The value equals the sysName object. - System Description-Description of the network entity (in alphanumeric format). This includes the system's name and versions of the hardware, operating system, and networking software supported by the switch. The value equals the sysDescr object. - System Capabilities-Primary functions of the switch, and whether or not these functions are enabled in the switch. The capabilities are indicated by two octets. Bits 0 through 7 indicate Other, Repeater, Bridge, WLAN AP, Router, Telephone, DOCSIS cable device, and station respectively. Bits 8 through 15 are reserved. - 802.3 MAC-PHY-Duplex and bit rate capability and the current duplex and bit rate settings of the sending device. It also indicates whether the current settings are due to auto-negotiation or manual configuration. - 802.3 Link Aggregation-Whether the link (associated with the port on which the LLDP PDU is transmitted) can be aggregated. It also indicates whether the link is currently aggregated, and if so, provides the aggregated port identifier. - 802.3 Maximum Frame-Maximum frame size capability of the MAC/ PHY implementation. The following fields relate to the Management Address: • Advertisement Mode-Select one of the following ways to advertise the IP management address of the switch: - Auto Advertise-Specifies that the software would automatically choose a management address to advertise from all the IP addresses of the product. In case of multiple IP addresses the software chooses the lowest IP address among the dynamic IP addresses. If there are no dynamic addresses, the software chooses the lowest IP address among the static IP addresses. - None-Do not advertise the management IP address. Cisco Small Business 200 Series Smart Switch Administration Guide 75

Section	Page
Getting Started	7
Starting the Web-based Switch Configuration Utility	7
Quick Start Switch Configuration	11
Interface Naming Conventions	11
Window Navigation	13
Viewing Statistics	17
Viewing Ethernet Interfaces	17
Viewing Etherlike Statistics	18
Viewing 802.1X EAP Statistics	19
Managing RMON	21
Managing System Logs	24
Setting System Log Settings	24
Setting Remote Logging Settings	26
Viewing Memory Logs	27
Managing System Files	29
Types of System Files	29
Upgrade/Backup Firmware/Language	32
Downloading or Backing-up a Configuration or Log	34
Viewing Configuration Files Properties	37
Copying Configuration Files	38
DHCP Auto Configuration	39
General Administrative Information	43
Switch Models	43
System Information	45
Rebooting the Switch	47
Monitoring the Fan Status and Temperature	48
Defining Idle Session Timeout	48
Pinging a Host	49
System Time	51
System Time Options	52
SNTP Modes	53
Configuring System Time	54
Managing Device Diagnostics	61
Testing Copper Ports	61
Displaying Optical Module Status	63
Configuring Port and VLAN Mirroring	64
Viewing CPU Utilization and Secure Core Technology	66
Configuring Discovery	68
Configuring Bonjour Discovery	68
LLDP and CDP	69
Configuring LLDP	70
Configuring CDP	91
Port Management	100
Configuring Ports	100
Setting Basic Port Configuration	101
Configuring Link Aggregation	103
Configuring Green Ethernet	111
Smartports	118
Overview	118
What is a Smartport	119
Smartport Types	119
Smartport Macros	122
Macro Failure and the Reset Operation	123
How the Smartport Feature Works	124
Auto Smartport	124
Error Handling	128
Default Configuration	128
Relationships with Other Features and Backwards Compatibility	129
Common Smartport Tasks	129
Configuring Smartport Using The Web-based Interface	131
Built-in Smartport Macros	136
Managing Power-over-Ethernet Devices	148
PoE on the Switch	148
Configuring PoE Properties	151
Configuring the PoE Power, Priority, and Class	152
VLAN Management	155
VLANs	155
Configuring Default VLAN Settings	158
Creating VLANs	159
Configuring VLAN Interface Settings	160
Defining VLAN Membership	161
Voice VLAN	165
Configuring the Spanning Tree Protocol	179
STP Flavors	179
Configuring STP Status and Global Settings	180
Defining Spanning Tree Interface Settings	182
Configuring Rapid Spanning Tree Settings	184
Managing MAC Address Tables	187
Configuring Static MAC Addresses	188
Managing Dynamic MAC Addresses	188
Configuring Multicast Forwarding	190
Multicast Forwarding	190
Defining Multicast Properties	193
Adding MAC Group Address	195
Adding IP Multicast Group Addresses	197
Configuring IGMP Snooping	198
MLD Snooping	200
Querying IGMP/MLD IP Multicast Group	203
Defining Multicast Router Ports	204
Defining Forward All Multicast	205
Defining Unregistered Multicast Settings	206
Configuring IP Information	207
Management and IP Interfaces	207
Configuring ARP	219
Domain Name Systems	220
Configuring Security	224
Defining Users	225
Configuring RADIUS	228
Configuring Management Access Authentication	230
Defining Management Access Method	231
Configuring TCP/UDP Services	236
Defining Storm Control	237
Configuring Port Security	238
Configuring 802.1X	241
Denial of Service Prevention	247
Using the SSL Feature	249
SSL Overview	249
Default Settings and Configuration	249
SSL Server Authentication Settings	250
Secure Sensitive Data	252
Introduction	252
SSD Rules	253
SSD Properties	258
Configuration Files	261
SSD Management Channels	266
Menu CLI and Password Recovery	266
Configuring SSD	267
Configuring Quality of Service	270
QoS Features and Components	271
Configuring QoS - General	272

Match case Limit results 1 per page

Configuring Discovery

Configuring LLDP

Cisco Small Business 200 Series Smart Switch Administration Guide

•

Available Optional TLVs

—Select the information to be published by the

switch by moving the TLV to the

Selected Optional TLVs

list. The available

TLVs contain the following information:

Port Description

—Information about the port, including manufacturer,

product name and hardware/software version.

System Name

—System's assigned name (in alpha-numeric format). The

value equals the sysName object.

System Description

—Description of the network entity (in alpha-

numeric format). This includes the system's name and versions of the

hardware, operating system, and networking software supported by the

switch. The value equals the sysDescr object.

System Capabilities

—Primary functions of the switch, and whether or

not these functions are enabled in the switch. The capabilities are

indicated by two octets. Bits 0 through 7 indicate Other, Repeater, Bridge,

WLAN AP, Router, Telephone, DOCSIS cable device, and station

respectively. Bits 8 through 15 are reserved.

802.3 MAC-PHY

—Duplex and bit rate capability and the current duplex

and bit rate settings of the sending device. It also indicates whether the

current settings are due to auto-negotiation or manual configuration.

802.3 Link Aggregation

—Whether the link (associated with the port on

which the LLDP PDU is transmitted) can be aggregated. It also indicates

whether the link is currently aggregated, and if so, provides the

aggregated port identifier.

802.3 Maximum Frame

—Maximum frame size capability of the MAC/

PHY implementation.

The following fields relate to the Management Address:

•

Advertisement Mode

—Select one of the following ways to advertise the IP

management address of the switch:

Auto Advertise

—Specifies that the software would automatically

choose a management address to advertise from all the IP addresses of

the product. In case of multiple IP addresses the software chooses the

lowest IP address among the dynamic IP addresses. If there are no

dynamic addresses, the software chooses the lowest IP address among

the static IP addresses.

None

—Do not advertise the management IP address.