Home » Compaq Manuals » Desktops » Compaq Pro 6305 » Manual Viewer

Compaq Pro 6305 Maintenance and Service Guide Pro 6305 Microtower Business PC - Page 203

Control panel message, Description, Recommended action, ME Firmware Version should

Add to My Manuals
Save this manual to your list of manuals

Page 203 highlights

Table 10-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 2203-Setup error during MEBx execution MEBx selection or exit resulted in a setup failure. 1. Reboot the computer. 2. Unplug the power cord, re-seat the memory modules, and reboot the computer. 3. If the memory configuration was recently changed, unplug the power cord, restore the original memory configuration, and reboot the computer. 4. If the error persists, replace the system board. 2204-Inventory error during MEBx execution BIOS information passed to the MEBx resulted in a failure. 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version. 3. If the error still persists, replace the system board. 2205-Interface error during MEBx execution MEBx operation experienced a hardware error during communication with ME. 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version. 3. If the error still persists, replace the system board. 2211-Memory not configured correctly for proper MEBx execution. DIMM1 or XMM1 is not installed. Make sure there is a memory module in the black DIMM1 socket and that it is properly seated. 2212-USB Key Provisioning failure writing to device USB device used for USB key provisioning will not allow BIOS to update provision file properly. 1. Try a different USB key device for provisioning. 2. If the error persists, update to the latest BIOS version and ME firmware version. 3. If the error still persists, replace the system board. 2217-ME Firmware Version request failure ME firmware is not properly responding to BIOS query for version information. 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version and ME firmware version. 3. If the error still persists, replace the system board. 2218-ME Firmware Version should be updated ME firmware must be updated to match current functionality contained in the system BIOS. 1. Update to the latest ME firmware version. 2. If the error persists and system BIOS has been recently updated, restore previous system BIOS version. 3. If the error still persists, replace the system board. POST Numeric Codes and Text Messages 193

Section	Page
Product Features	11
Standard Configuration Features	11
Microtower (MT) Front Panel Components	12
Small Form Factor (SFF) Front Panel Components	13
Microtower (MT) Rear Panel Components	14
Small Form Factor (SFF) Rear Panel Components	15
Serial Number Location	16
Activating and Customizing the Software	17
Activating and customizing the software in Windows 7	17
Activating the Windows operating system	17
Downloading Windows 7 updates	18
Installing or upgrading device drivers	18
Customizing the monitor display	18
Activating and customizing the software in Windows 8	18
Activating the Windows Operating System	18
Downloading Windows 8 updates	19
Customizing the monitor display	19
Computer Setup (F10) Utility	20
Computer Setup (F10) Utilities	20
Using Computer Setup (F10) Utilities	21
Computer Setup—File	22
Computer Setup—Storage	23
Computer Setup—Security	26
Computer Setup—Power	31
Computer Setup—Advanced	32
Recovering the Configuration Settings	34
Illustrated parts catalog	35
Microtower (MT) chassis spare parts	35
Computer major components	35
Cables	37
Misc parts	38
Drives	40
Misc boards	40
Sequential part number listing	41
Small Form Factor (SFF) chassis spare parts	45
Computer major components	45
Cables	47
Misc parts	48
Drives	50
Misc boards	50
Sequential part number listing	51
Routine Care, SATA Drive Guidelines, and Disassembly Preparation	55
Electrostatic Discharge Information	55
Generating Static	55
Preventing Electrostatic Damage to Equipment	56
Personal Grounding Methods and Equipment	56
Grounding the Work Area	57
Recommended Materials and Equipment	57
Operating Guidelines	58
Routine Care	58
General Cleaning Safety Precautions	58
Cleaning the Computer Case	59
Cleaning the Keyboard	59
Cleaning the Monitor	59
Cleaning the Mouse	60
Service Considerations	60
Power Supply Fan	60
Tools and Software Requirements	60
Screws	60
Cables and Connectors	61
Hard Drives	61
Lithium Coin Cell Battery	61
SATA Hard Drives	62
SATA Hard Drive Cables	62
SATA Data Cable	62
SMART ATA Drives	62
Cable Management	62
Hard Drive Capacities	63
Removal and Replacement Procedures Microtower (MT) Chassis	64
Preparation for Disassembly	64
Computer Access Panel	65
Front Bezel	66
Front Bezel Security	67
Bezel Blanks	69
Memory	70
DIMMs	70
DDR3-SDRAM DIMMs	70
Populating DIMM Sockets	71
Installing DIMMs	72
Expansion Cards	74
WLAN module	77
System Board Connections	79
Drives	80
Drive Positions	82
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay	83
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay	85
Removing a Hard Drive from a Drive Bay	87
Installing a Hard Drive into an Internal Drive Bay	88
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	90
Front Fan Assembly	95
Front I/O Assembly	96
Power Switch/LED Assembly	97
Heat sink	99
Processor	100
Speaker	101
Rear Chassis Fan	103
Power Supply	105
System Board	106
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	109
Preparation for Disassembly	109
Access Panel	110
Front Bezel	111
Front Bezel Security	112
Bezel Blanks	114
Memory	115
DIMMs	115
DDR3-SDRAM DIMMs	115
Populating DIMM Sockets	116
Installing DIMMs	117
Expansion Card	119
WLAN module	123
System Board Connections	125
Drives	126
Drive Positions	127
Installing and Removing Drives	127
Removing a 5.25-inch Drive from a Drive Bay	129
Installing a 5.25-inch Drive into a Drive Bay	129
Removing a 3.5-inch Drive from a Drive Bay	131
Installing a 3.5-inch Drive into a Drive Bay	133
Removing and Replacing the Primary 3.5-inch Internal Hard Drive	135
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	137
Fan duct	142
Front Fan Assembly	143
Hood Sensor	145
Front I/O, Power Switch Assembly	146
Speaker	148
Heat sink	149
Processor	151
Power Supply	152
System Board	153
Using the Small Form Factor Computer in a Tower Orientation	155
Troubleshooting Without Diagnostics	156
Safety and Comfort	156
Before You Call for Technical Support	156
Helpful Hints	157
Solving General Problems	158
Solving Power Problems	162
Solving Hard Drive Problems	164
Solving Media Card Reader Problems	166
Solving Display Problems	168
Solving Audio Problems	173
Solving Printer Problems	175
Solving Keyboard and Mouse Problems	176
Solving Hardware Installation Problems	179
Solving Network Problems	181
Solving Memory Problems	185
Solving Processor Problems	186
Solving CD-ROM and DVD Problems	187
Solving USB Flash Drive Problems	189
Solving Front Panel Component Problems	190
Solving Internet Access Problems	191
Solving Software Problems	192
Contacting Customer Support	194
HP PC Hardware Diagnostics	195
Why run HP PC Hardware Diagnostics – UEFI	195
How to access and run HP PC Hardware Diagnostics - UEFI	195
Downloading HP PC Hardware Diagnostics to a USB device	196
POST Error Messages	197
POST Numeric Codes and Text Messages	197
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	205
Password Security and Resetting CMOS	209
Resetting the Password Jumper	209
Clearing and Resetting the CMOS	210
Backup and Recovery	213
Restoring and recovering in Windows 7	213
System Restore	213
System Recovery	213
System Recovery when Windows is responding	214
System Recovery when Windows is not responding	215
System recovery using recovery media	215
Creating recovery media	216
Using recovery media	217
Backup and recovery in Windows 8	217
Backing up your information	218
Performing a system recovery	218
Using the Windows recovery tools	219
Using f11 recovery tools	219
Using Windows 8 operating system media (purchased separately)	220
Battery Replacement	221
Power Cord Set Requirements	224
General Requirements	224
Japanese Power Cord Requirements	224
Country-Specific Requirements	225
Specifications	226
MT Specifications	226
SFF Specifications	227

Match case Limit results 1 per page

Table 10-1

Numeric Codes and Text Messages (continued)

Control panel message

Description

Recommended action

2203-Setup error during MEBx execution

MEBx selection or exit resulted in a setup

failure.

Reboot the computer.

Unplug the power cord, re-seat the

memory modules, and reboot the

computer.

If the memory configuration was

recently changed, unplug the power

cord, restore the original memory

configuration, and reboot the computer.

If the error persists, replace the system

board.

2204-Inventory error during MEBx execution

BIOS information passed to the MEBx

resulted in a failure.

Reboot the computer.

If the error persists, update to the latest

BIOS version.

If the error still persists, replace the

system board.

2205-Interface error during MEBx execution

MEBx operation experienced a hardware

error during communication with ME.

Reboot the computer.

If the error persists, update to the latest

BIOS version.

If the error still persists, replace the

system board.

2211-Memory not configured correctly for

proper MEBx execution.

DIMM1 or XMM1 is not installed.

Make sure there is a memory module in the

black DIMM1 socket and that it is properly

seated.

2212-USB Key Provisioning failure writing to

device

USB device used for USB key provisioning

will not allow BIOS to update provision file

properly.

Try a different USB key device for

provisioning.

If the error persists, update to the latest

BIOS version and ME firmware version.

If the error still persists, replace the

system board.

2217-ME Firmware Version request failure

ME firmware is not properly responding to

BIOS query for version information.

Reboot the computer.

If the error persists, update to the latest

BIOS version and ME firmware version.

If the error still persists, replace the

system board.

2218-ME Firmware Version should be

updated

ME firmware must be updated to match

current functionality contained in the system

BIOS.

Update to the latest ME firmware

version.

If the error persists and system BIOS

has been recently updated, restore

previous system BIOS version.

If the error still persists, replace the

system board.

POST Numeric Codes and Text Messages

193