Cub Cadet CC 30 e Electric Rider Operation Manual - Page 10

OPERATION Note: The brake pedal must be fully depressed to start the tractor. Refer to Safety Interlock Switches for more information. Park Brake Lever (F) The Park Brake Lever is located on the right side of the steering column and is used to engage the parking brake. Refer to Engaging the Parking Brake section of this manual for detailed instructions regarding setting the parking brake. Refer to Releasing the Parking brake section of this manual for instructions regarding releasing the parking brake. Deck Lift Lever (G) Located on your tractor's right fender, the deck lift lever is used to change the height of the cutting deck (5 positions). To use the deck lift lever, move the lever to the left, then place in the notch best suited for your application. The lowest position is "1" and the highest position is "5". Position "1" is approximately a 1" cutting height, Position "5" is approximately a 4" cutting height and the change in height is approximately 3/4" between each position. Headlight (H) The headlights will turn ON whenever the key is ON and the headlight button is pressed. To turn the headlights OFF, press the headlight button again. Charging Port (I) The charging port is located on the rear of the tractor. To access the charging port, lift up on the charging port cover. USB Charging Ports (J) (If Equipped) If equipped, a pair of USB power sources are located on the left console. The two USB ports are both rated 2.1 A. The ports can be used to charge your phone or power up other USB devices. WARNING Do not have any devices plugged into your USB charging ports when starting the tractor. Doing so may cause damage to your device. Cup Holder (K) The cup holder is located to the left of the operator's seat. Operation Safety Interlock System This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact an authorized service dealer. • • The safety interlock system prevents the operator from turning the tractor ON unless the operator is in the seat with the parking brake engaged or brake pedal fully depressed and the drive pedal in the NEUTRAL position. • The tractor will not operate with the charger cord plugged into the charging port and/or the charging port cover open or removed. • The tractor will automatically shut off the blade(s) and drive motors if the operator leaves the seat. Note: To restart the tractor, follow the proper starting procedures as instructed in Starting the Tractor section on this page. Engaging the Parking Brake 1. Fully depress the brake pedal and hold it down with your foot. 2. Move the parking brake lever back into the parking brake position. 3. Release the brake pedal to allow the parking brake to engage. Releasing the Parking Brake 1. Depress the brake pedal. 2. Move the parking brake lever forward out of the parking brake position. 3. Release the brake pedal. Setting the Cutting Height Select the height position of the cutting deck by placing the deck lift lever in any of the five (5) different cutting height notches on the right side of the fender. WARNING Keep hands and feet away from the discharge opening of the cutting deck. Refer to Leveling the Deck in the Service & Maintenance section of this manual for more detailed instructions regarding deck adjustment. Starting the Tractor 1. Unplug the charging cord (if necessary). If the cord is still plugged in, a reminder will display on the VCM when the key switch is turned on. 2. Sit in the operator's seat. Insert the key into the key switch Note: A reminder will display on the VCM if the operator is not in the seat when the key switch is turned on. 3. Fully depress the brake pedal or set the parking brake. Note: If the brake is not engaged a reminder will display on the VCM when the key switch is turned on. 4. Turn the key clockwise to the ON (I) position. 5. Press the start/stop button down until you hear two beeps. Note: The VCM and drive motors are now activated and the tractor is ready to be operated. Stopping the Tractor WARNING If you strike a foreign object, stop the tractor, turn the key to OFF and remove. Thoroughly inspect the machine for any damage. Repair the damage before restarting and operating. 1. If the blade is engaged (blades ON), press the PTO button to disengage the blades (blades OFF) and engage the parking brake. 2. Press the start/stop button (you will hear one beep) or turn the key counterclockwise to the OFF (O) position. 3. Remove the key to prevent unauthorized use by children or others. Driving the Tractor WARNING Do not operate the tractor if the safety interlock system is malfunctioning. This system was designed for your safety and protection. WARNING • Avoid sudden starts, excessive speed and sudden stops. • Do not leave the seat of the tractor without first pressing the PTO button to turn off the blade(s), and engaging the parking brake. If leaving the tractor unattended, turn the key to the OFF position and remove. • Always look down and behind before and while backing up to avoid a back-over accident. 1. Disengage the parking brake 10