D-Link DCH-M225 User Manual - Page 31

Network Settings, Advanced Settings

Get D-Link DCH-M225 PDF manuals and user guides View all D-Link DCH-M225 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Section 3 - Configuration Network Settings This page allows you to configure the Network Settings for the DCH-M225. To access this page from the Home page, click on the Settings drop-down menu at the top of the page, and select Network. Management You can change the device name in the management link Link: by editing the text in the text box. If you change this device name, you will need to enter http://xxxx.local./ (where "xxxx"corresponds to the name of the device) in the address bar of your web browser in order to access the configuration utility. Advanced Settings The Advanced Settings section of the Network Settings page allows you to configure both IPv4 and IPv6 settings that will be used by the DCH-M225's extended network. IPv4 Device Management Interface My LAN Select whether you want the IP to have a Dynamic IP (DHCP) Connection is: or Static IP address. Select Dynamic IP to obtain the IP address information automatically from your ISP (Internet Service Provider.) If you choose Dynamic IP, the fields below will be greyed-out. IP Address: Enter the Static IP Address you want to assign to the extended network AP. This address should be outside of the uplink router's DHCP address pool. Subnet Mask: Enter the Subnet Mask. Gateway Enter the Gateway Address. (Usually this is the IP address Address: of the uplink router.) D-Link DCH-M225 User Manual 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
27
D-Link DCH-M225 User Manual
Section 3 - Configuration
Network Settings
This page allows you to configure the
Network Settings
for the DCH-M225. To access this page from the
Home
page, click on the
Settings
drop-down menu at the top of the page, and select
Network
.
Management
Link:
You can change the device name in the management link
by editing the text in the text box. If you change this device
name, you will need to enter
(where
“xxxx” corresponds to the name of the device) in the address
bar of your web browser in order to access the configuration
utility.
Advanced Settings
The
Advanced Settings
section of the
Network Settings
page allows you to configure both
IPv4
and
IPv6
settings that will be
used by the DCH-M225’s extended network.
My LAN
Connection is:
IP Address:
Subnet Mask:
Gateway
Address:
Select whether you want the IP to have a
Dynamic IP (DHCP)
or
Static IP
address. Select
Dynamic IP
to obtain the IP
address information automatically from your ISP (Internet
Service Provider.) If you choose
Dynamic IP
, the fields below
will be greyed-out.
Enter the
Static IP Address
you want to assign to the
extended network AP. This address should be outside of the
uplink router’s DHCP address pool.
Enter the
Subnet Mask
.
Enter the
Gateway Address
. (Usually this is the IP address
of the uplink router.)
IPv4 Device Management Interface