D-Link DE-1824EI User Guide - Page 83

Cables and Connectors

Get D-Link DE-1824EI - Hub - EN PDF manuals and user guides
UPC - 790069217593
View all D-Link DE-1824EI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

10BASE-T Stackable Hubs D DCABLES AND CONNECTORS Ports 2 through 24 are MDI-X 10BASE-T Ethernet ports. Port 1 is a 10BASE-T Ethernet port, with a sliding switch that enables a connection to a network station (in the MDI-X setting) or to a repeater, bridge, or hub (in the MDI setting). 10BASE-T connections require a twisted-pair cable, a maximum of 100 meters long, with RJ-45 connectors at both ends. You can use shielded twisted-pair cable or 0.4-0.6 mm (22-26 AWG) 8-wire unshielded twisted-pair cable for the connection. The following diagram and table show a standard RJ-45 receptacle/connector and its pin assignments. Numbering of the pins and contacts shown in the diagram correspond to the entries in the subsequent table. Only pin/contact signals relevant to the hub are listed. Figure D-1 RJ-45 Connectors Contact 1 RJ-45 Connector MDI-X Signal MDI Signal RD+ (receive) TD+ (transmit) Cables and Connectors D-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
10BASE-T Stackable Hubs
Cables and Connectors
D-1
D
D
C
ABLES AND
C
ONNECTORS
Ports 2 through 24 are MDI-X 10BASE-T Ethernet ports. Port 1 is a
10BASE-T Ethernet port, with a sliding switch that enables a connection to a
network station (in the MDI-X setting) or to a repeater, bridge, or hub (in the
MDI setting). 10BASE-T connections require a twisted-pair cable, a
maximum of 100 meters long, with RJ-45 connectors at both ends. You can
use shielded twisted-pair cable or 0.4-0.6 mm (22-26 AWG) 8-wire
unshielded twisted-pair cable for the connection.
The
following
diagram
and
table
show
a
standard
RJ-45
receptacle/connector and its pin assignments. Numbering of the pins and
contacts shown in the diagram correspond to the entries in the subsequent
table. Only pin/contact signals relevant to the hub are listed.
Figure D-1
RJ-45 Connectors
RJ-45 Connector
Contact
MDI-X Signal
MDI Signal
1
RD+ (receive)
TD+ (transmit)