D-Link DGS-1510 Quick Install Guide - Page 30

Connecting to the Switch for the First Time - d link 28xmp

Get D-Link DGS-1510 PDF manuals and user guides View all D-Link DGS-1510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide Connecting to the Switch for the First Time After successfully connecting to the Switch's console and the Switch was turned on, the boot-up procedure will be displayed, as shown below. Boot Procedure V1.00.016 Power On Self Test 100 % MAC Address : 3C-1E-04-A1-B9-E0 H/W Version : A1 Please Wait, Loading V1.70.005 Runtime Image UART init Starting runtime image Device Discovery Configuration init 100 % 100 % 100 % 100 % Switch con0 is now available Press any key to login... During the boot-up procedure, we can find the PROM version, MAC address, Hardware Version, and Firmware Version used by this Switch. NOTE: Both the default username and password is admin. Enter the username and password when prompt to do so and press enter after each entry. The CLI prompt will immediately be available, as shown below. DGS-1510-28XMP Gigabit Ethernet SmartPro Switch Command Line Interface Firmware: Build 1.70.005 Copyright(C) 2020 D-Link Corporation. All rights reserved. User Access Verification Username:admin Password:***** Switch# Now the Switch can be configured. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide
30
Connecting to the Switch for the First Time
After successfully connecting to the Switch’s console and the Switch was turned on, the boot-up
procedure will be displayed, as shown below.
Boot Procedure
V1.00.016
-------------------------------------------------------------------------------
Power On Self Test
........................................
100 %
MAC Address
: 3C-1E-04-A1-B9-E0
H/W Version
: A1
Please Wait, Loading V1.70.005 Runtime Image
..............
100 %
UART init
.................................................
100 %
Starting runtime image
Device Discovery
..........................................
100 %
Configuration init
........................................
100 %
Switch con0 is now available
Press any key to login...
During the boot-up procedure, we can find the PROM version, MAC address, Hardware Version, and
Firmware Version used by this Switch.
NOTE:
Both the default
username
and
password
is
admin
.
Enter the username and password when prompt to do so and press enter after each entry. The CLI
prompt will immediately be available, as shown below.
DGS-1510-28XMP Gigabit Ethernet SmartPro Switch
Command Line Interface
Firmware: Build 1.70.005
Copyright(C) 2020 D-Link Corporation. All rights reserved.
User Access Verification
Username:admin
Password:*****
Switch#
Now the Switch can be configured.