Dell Alienware m17 Service Manual - Page 65

Removing the display assembly, Prerequisites, Procedure

Get Dell Alienware m17 PDF manuals and user guides View all Dell Alienware m17 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Removing the display assembly WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites 1 Remove the base cover. 2 Remove the wireless card. Procedure 1 Remove the two screws (M2x3) that secure the power-adapter port bracket to the palm-rest assembly. 2 Lift the power-adapter port bracket off the palm-rest assembly. 3 Lift the power-adapter port off the palm-rest assembly, moving it away from the display hinge. 4 Peel the tape that secures the camera cable to the system board and disconnect the camera cable. 5 Peel the tape that secures the display-cable connector latch to the system board. 6 Open the latch and disconnect the display cable from the system board. 7 Open the display at an angle of 90 degrees and place the computer at the edge of the table. 8 Remove the two screws (M2.5x4.5) that secures the display hinges to the palm-rest assembly. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Removing the display assembly
WARNING: Before working inside your computer, read the safety information that shipped with your computer and
follow the steps in
Before working inside your computer
. After working inside your computer, follow the instructions
in
After working inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance
.
Prerequisites
1
Remove the
base cover
.
2
Remove the
wireless card
.
Procedure
1
Remove the two screws (M2x3) that secure the power-adapter port bracket to the palm-rest assembly.
2
Lift the power-adapter port bracket off the palm-rest assembly.
3
Lift the power-adapter port off the palm-rest assembly, moving it away from the display hinge.
4
Peel the tape that secures the camera cable to the system board and disconnect the camera cable.
5
Peel the tape that secures the display-cable connector latch to the system board.
6
Open the latch and disconnect the display cable from the system board.
7
Open the display at an angle of 90 degrees and place the computer at the edge of the table.
8
Remove the two screws (M2.5x4.5) that secures the display hinges to the palm-rest assembly.
65