Dell Inspiron 16 5635 Owners Manual - Page 59

Power button, Removing the power button

Get Dell Inspiron 16 5635 PDF manuals and user guides View all Dell Inspiron 16 5635 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

7. Close the left display hinge and align the screw holes on the left display hinge with the screw holes on the palm-rest and keyboard assembly. 8. Replace the two screws (M2.5x5) to secure the left display hinge to the palm-rest and keyboard assembly. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Power button Removing the power button Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task NOTE: Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer. The following image(s) indicate the location of the power button and provides a visual representation of the removal procedure. Steps 1. Remove the two screws (M2.5x5) that secure the left display hinge to the system board. 2. Open the left display hinge at an angle of 90 degrees. 3. Remove the two screws (M2x3) that secure the power-button board to the palm-rest and keyboard assembly. 4. Open the latch and disconnect the power-button board cable from the I/O board. 5. Lift the power-button board off the palm-rest and keyboard assembly. 6. Lift the power button off the palm-rest and keyboard assembly. Removing and installing Field Replaceable Units (FRUs) 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
7.
Close the left display hinge and align the screw holes on the left display hinge with the screw holes on the palm-rest and
keyboard assembly.
8.
Replace the two screws (M2.5x5) to secure the left display hinge to the palm-rest and keyboard assembly.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Power button
Removing the power button
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
NOTE:
Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer.
The following image(s) indicate the location of the power button and provides a visual representation of the removal procedure.
Steps
1.
Remove the two screws (M2.5x5) that secure the left display hinge to the system board.
2.
Open the left display hinge at an angle of 90 degrees.
3.
Remove the two screws (M2x3) that secure the power-button board to the palm-rest and keyboard assembly.
4.
Open the latch and disconnect the power-button board cable from the I/O board.
5.
Lift the power-button board off the palm-rest and keyboard assembly.
6.
Lift the power button off the palm-rest and keyboard assembly.
Removing and installing Field Replaceable Units (FRUs)
59