Dell Inspiron 16 5635 Owners Manual - Page 64

Installing the display assembly

Get Dell Inspiron 16 5635 PDF manuals and user guides View all Dell Inspiron 16 5635 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Steps 1. Peel the tape that secures the display-cable connector latch to the system board. 2. Open the latch and disconnect the display cable from the system board. 3. Remove the two screws (M2.5x5) that secure the left display hinge to the system board. 4. Open the left display hinge at an angle of 90 degrees. 5. Remove the three screws (M2.5x5) that secure the right display hinge to the system board. 6. Open the right display hinge at an angle of 90 degrees. 7. At an angle, gently lift the palm-rest and keyboard assembly off the display assembly. Installing the display assembly Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the display assembly and provides a visual representation of the installation procedure. 64 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Steps
1.
Peel the tape that secures the display-cable connector latch to the system board.
2.
Open the latch and disconnect the display cable from the system board.
3.
Remove the two screws (M2.5x5) that secure the left display hinge to the system board.
4.
Open the left display hinge at an angle of 90 degrees.
5.
Remove the three screws (M2.5x5) that secure the right display hinge to the system board.
6.
Open the right display hinge at an angle of 90 degrees.
7.
At an angle, gently lift the palm-rest and keyboard assembly off the display assembly.
Installing the display assembly
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the display assembly and provides a visual representation of the installation
procedure.
64
Removing and installing Field Replaceable Units (FRUs)