Dell Inspiron Mini 1012 Service Manual - Page 26

I/O Board

Get Dell Inspiron Mini 1012 PDF manuals and user guides View all Dell Inspiron Mini 1012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Back to Contents Page I/O Board Dell™ Inspiron™ 1012 Service Manual Removing the I/O Board Replacing the I/O Board WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. Removing the I/O Board 1. Follow the procedures in Before You Begin. 2. Remove the battery (see Removing the Battery). 3. Remove the keyboard (see Removing the Keyboard). 4. Remove the hard-drive assembly (see Removing the Hard-Drive Assembly). 5. Remove the palm rest assembly (see Removing the Palm Rest Assembly). 6. Remove the hinge cover (see Removing the Hinge Cover). 7. Remove the display assembly (see Removing the Display Assembly). 8. Remove the left support bracket (see Removing the Left Support Bracket). 9. Remove the speakers (see Removing the Speakers). 10. Press and eject any installed card or blank from the 3-in-1 Media Card Reader. 11. Lift the locking tab and pull the pull-tab on the status light board cable and disconnect the cable from the connector on the I/O board. 12. Disconnect the I/O board cable from the connector on the I/O board. 1 status light board cable

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Back to Contents Page
I/O Board
Dell™ Inspiron™ 1012 Service Manual
Removing the I/O Board
Replacing the I/O Board
Removing the I/O Board
1.
Follow the procedures in
Before You Begin
.
2.
Remove the battery (see
Removing the Battery
).
3.
Remove the keyboard (see
Removing the Keyboard
).
4.
Remove the hard-drive assembly (see
Removing the Hard
-
Drive Assembly
).
5.
Remove the palm rest assembly (see
Removing the Palm Rest Assembly
).
6.
Remove the hinge cover (see
Removing the Hinge Cover
).
7.
Remove the display assembly (see
Removing the Display Assembly
).
8.
Remove the left support bracket (see
Removing the Left Support Bracket
).
9.
Remove the speakers (see
Removing the Speakers
).
10.
Press and eject any installed card or blank from the 3-in-1 Media Card Reader.
11.
Lift the locking tab and pull the pull-tab on the status light board cable and disconnect the cable from the connector on the I/O board.
12.
Disconnect the I/O board cable from the connector on the I/O board.
WARNING:
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION:
Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™
is not covered by your warranty.
CAUTION:
To help prevent damage to the system board, remove the main battery (see
Removing the Battery
) before working inside the
computer.
1
status light board cable