Dell M410HD User Guide - Page 14

Using Your Projector, Turning Your Projector On, Turning Your Projector Off - projector no signal

Get Dell M410HD PDF manuals and user guides
UPC - 884116026440
View all Dell M410HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3 Using Your Projector Turning Your Projector On NOTE: Turn on the projector before you turn on the source (computer, DVD player, etc.). The Power button light blinks blue until pressed. 1 Remove the lens cap. 2 Connect the power cord and appropriate signal cables. For information about connecting the projector, see "Connecting Your Projector" on page 8. 3 Press the Power button (see "Using the Control Panel" on page 18 to locate the Power button). 4 Turn on your source (computer, DVD player, etc.) 5 Connect your source to the projector using the appropriate cable. See "Connecting Your Projector" on page 8 for instructions to connect your source to the projector. 6 By default, the input source of projector is set to VGA-In. Change the input source of projector if necessary. 7 If you have multiple sources connected to the projector, press the Source button on the remote control or control panel to select the desired source. See "Using the Control Panel" on page 18 and "Using the Remote Control" on page 21 to locate the Source button. Turning Your Projector Off NOTICE: Unplug the projector after properly shutting down as explained in the following procedure. 1 Press the Power button. NOTE: The "Press Power Button to Turn off Projector" message will appear on the screen. The message disappears after 5 seconds or you can press the Menu button to clear it. 2 Press the Power button again. The cooling fans continue to operate for 120 seconds. 14 Using Your Projector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
14
Using Your Projector
3
Using Your Projector
Turning Your Projector On
NOTE:
Turn on the projector before you turn on the source (computer, DVD
player, etc.). The
Power
button light blinks blue until pressed.
1
Remove the lens cap.
2
Connect the power cord and appropriate signal cables. For information about
connecting the projector, see "Connecting Your Projector" on page 8.
3
Press the
Power
button (see "Using the Control Panel" on page 18 to locate the
Power
button).
4
Turn on your source (computer, DVD player, etc.)
5
Connect your source to the projector using the appropriate cable. See
"Connecting Your Projector" on page 8 for instructions to connect your source
to the projector.
6
By default, the input source of projector is set to VGA-In. Change the input
source of projector if necessary.
7
If you have multiple sources connected to the projector, press the
Source
button on the remote control or control panel to select the desired source. See
"Using the Control Panel" on page 18 and "Using the Remote Control" on
page 21 to locate the
Source
button.
Turning Your Projector Off
NOTICE:
Unplug the projector after properly shutting down as explained in the
following procedure.
1
Press the
Power
button.
NOTE:
The "
Press Power Button to Turn off Projector
" message will
appear on the screen. The message disappears after 5 seconds or you can
press the
Menu
button to clear it.
2
Press the
Power
button again. The cooling fans continue to operate for 120
seconds.