Dell OptiPlex 7080 Tower Service Manual - Page 37

Memory modules, Removing the memory modules

Get Dell OptiPlex 7080 Tower PDF manuals and user guides View all Dell OptiPlex 7080 Tower manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive connector. 2. Insert the solid-state drive at a 45-degree angle into the slot on the system board. 3. Replace the screw (M2x3.5) to secure the M.2 2280 solid-state drive to the system board. NOTE: Repeat the above procedure for installing the other solid-state drive. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Memory modules Removing the memory modules Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the memory modules and provide a visual representation of the removal procedure. Steps 1. Pull the securing clips from both side of the memory module until the memory module pops up. 2. Slide and remove the memory module from the memory-module slot. Disassembly and reassembly 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Steps
1.
Align the notch on the solid-state drive with the tab on the solid-state drive connector.
2.
Insert the solid-state drive at a 45-degree angle into the slot on the system board.
3.
Replace the screw (M2x3.5) to secure the M.2 2280 solid-state drive to the system board.
NOTE:
Repeat the above procedure for installing the other solid-state drive.
Next steps
1.
Install the
side cover
.
2.
Follow the procedure in
after working inside your computer
.
Memory modules
Removing the memory modules
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
About this task
The following images indicate the location of the memory modules and provide a visual representation of the removal procedure.
Steps
1.
Pull the securing clips from both side of the memory module until the memory module pops up.
2.
Slide and remove the memory module from the memory-module slot.
Disassembly and reassembly
37