Dell PowerEdge R830 EMC PowerEdge Servers Troubleshooting Guide - Page 113

Symptoms, Linux, FAQs, Installing operating system through various methods

Get Dell PowerEdge R830 PDF manuals and user guides View all Dell PowerEdge R830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

To fix the issue, ioSphere needs to be reinstalled. The link below contains information about installing, updating and managing Fusion-IO, which contains information about installing ioSphere: http://www.dell.com/support/article/au/en/audhs1/sln156793/how-to-install-update-and-manage-fusion-io-drives-in-windows-os-ondell-poweredge-servers?lang=en Symptoms Dell PowerEdge Express Flash NVMe PCIe SSD device is not detected during hot-plug in ESXi 6.0 Description When the Express Flash NVMe PCIe SSD namespace is set as Offline and hot-plug operation is performed in the same slot, the SSD does not initialize and is not detected. This is a known issue. Perform one of the following steps: 1. Reconnect the drive to a different drive slot, if available. 2. Restart the sfcbd-watchdog service and reinsert the drive. Linux FAQs Why are network ports displayed as unknown in YaST2 network configuration in SUSE Linux Enterprise? While configuring a bonding interface, the configured bond-slaves are listed as Unknown Network Device. The YaST installer is unable to write the device name in to the ifcfg files. Delete the existing configuration of previously configured network interfaces. Symptoms Unable to boot from iSCSI when static IPv6 address is assigned to the initiator Description The SUSE Linux Enterprise Server 12 does not boot from iSCSI over IPv6 address after successful installation, when static IPv6 address is assigned to the initiator. Resolution Use Dynamic Host Configuration Protocol (DHCP) address for the initiator. Installing operating system through various methods Install and deploy operating system through Dell Lifecycle Controller and various methods, watch the following videos listed below: Table 22. Installation of OS through LC and various methods Slno 1. Video Description Launching Lifecycle Controller Location Launching LC 2. Dell Lifecycle Controller - Firmware Rollback LC Firmware Rollback Troubleshooting operating system issues 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
To fix the issue, ioSphere needs to be reinstalled. The link below contains information about installing, updating and managing Fusion-IO,
which contains information about installing ioSphere:
dell-poweredge-servers?lang=en
Symptoms
Dell PowerEdge Express Flash NVMe PCIe SSD device is not detected
during hot-plug in ESXi 6.0
Description
When the Express Flash NVMe PCIe SSD namespace is set as Offline and hot-plug operation is performed in the same slot, the SSD does
not initialize and is not detected.
This is a known issue. Perform one of the following steps:
1.
Reconnect the drive to a different drive slot, if available.
2.
Restart the sfcbd-watchdog service and reinsert the drive.
Linux
FAQs
Why are network ports displayed as unknown in YaST2 network
configuration in SUSE Linux Enterprise?
While configuring a bonding interface, the configured bond-slaves are listed as Unknown Network Device. The YaST installer is unable to
write the device name in to the ifcfg files. Delete the existing configuration of previously configured network interfaces.
Symptoms
Unable to boot from iSCSI when static IPv6 address is assigned to the
initiator
Description
The SUSE Linux Enterprise Server 12 does not boot from iSCSI over IPv6 address after successful installation, when static IPv6 address is
assigned to the initiator.
Resolution
Use Dynamic Host Configuration Protocol (DHCP) address for the initiator.
Installing operating system through various
methods
Install and deploy operating system through Dell Lifecycle Controller and various methods, watch the following videos listed below:
Table 22. Installation of OS through LC and various methods
Slno
Video Description
Location
1.
Launching Lifecycle Controller
Launching LC
2.
Dell Lifecycle Controller - Firmware Rollback
LC Firmware Rollback
Troubleshooting operating system issues
113