Dell PowerSwitch S4112F-ON Open Networking Hardware Diagnostic Guide April 201 - Page 12

Installation ONIE from BIOS

Get Dell PowerSwitch S4112F-ON PDF manuals and user guides View all Dell PowerSwitch S4112F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

6 Start TFTP waterfall-from the DHCPv4 option 66. ONIE ifconfig eth0 command examples If none of the ONIE Service Discovery methods are successful, you can disable this using the onie-discovery-stop command. You can install an operating system manually from HTTP, USB, FTP, or TFTP using the onie-nos-install command. NOTE: If you have a recovery USB plugged into your system, you must remove it using the onie-nos-install command. The ONIE Install environment uses DHCP to assign an IP address to the management interface, eth0. If that fails, it uses the link-local IPv4 address 169.254.209.190/16. To display the IP address, use the ifconfig eth0 command, as shown: ONIE:/ # ifconfig eth0 eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76 inet addr:x.x.x.x Bcast:x.x.x.x Mask:x.x.x.x inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB) Interrupt:21 Memory:ff300000-ff320000 To assign an IP address to the management interface, eth0, and verify network connectivity, use the ifconfig eth0 command, as shown: ONIE:/ # ifconfig eth0 x.x.x.x netmask x.x.x.x UP Then set speed on management interface as below ONIE:/ # ethtool -s eth0 speed 100 duplex full Verify the network connection with ping. ONIE:/ # ping x.x.x.x PING x.x.x.x (x.x.x.x): 56 data bytes 64 bytes from x.x.x.x: seq=0 ttl=62 time=1.357 ms 64 bytes from x.x.x.x: seq=1 ttl=62 time=0.577 ms ^C Installation ONIE from BIOS Install ONIE from the BIOS using the media (usb) boot-the ONIE installer USB. Pre-requisites The BIOS running on your system must meet the following requirements: • Allows a change to the boot order so the system can boot from media (USB). • Allows a baud-rate change. This feature is optional; you do not need it if your BIOS is running at 115200 baud rate. The default baud rate for ONIE is 115200. CAUTION: • These procedures are for x86-based targets only, particularly targets using Rangeley or Centerton CPU-based boards. • Check the console (UART-0/1) used on the target. • The log messages included in this guide are subject to change. NOTE: The following procedure is generic and does not list a particular target. Therefore, the ONIE images are specified using the _ notation. For example, the ONIE media (usb) iso image is onie-recovery-x86_64dell__-r0.iso. 12 ONIE installation instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
6
Start TFTP waterfall—from the DHCPv4 option 66.
ONIE
ifconfig eth0
command examples
If none of the ONIE Service Discovery methods are successful, you can disable this using the
onie-discovery-stop
command.
You can install an operating system manually from HTTP, USB, FTP, or TFTP using the
onie-nos-install <
URL
>
command.
NOTE:
If you have a recovery USB plugged into your system, you must remove it using the
onie-nos-install <
URL
>
command.
The ONIE Install environment uses DHCP to assign an IP address to the management interface,
eth0
. If that fails, it uses the link-local
IPv4 address 169.254.209.190/16.
To display the IP address, use the
ifconfig eth0
command, as shown:
ONIE:/ #
ifconfig
eth0
eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76
inet addr:x.x.x.x Bcast:x.x.x.x Mask:x.x.x.x
inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB)
Interrupt:21 Memory:ff300000-ff320000
To assign an IP address to the management interface,
eth0
, and verify network connectivity, use the
ifconfig eth0
<ip
address>
command, as shown:
ONIE:/ #
ifconfig
eth0 x.x.x.x netmask x.x.x.x UP
Then set speed on management interface as below
ONIE:/ # ethtool -s eth0 speed 100 duplex full
Verify the network connection with ping.
ONIE:/ # ping x.x.x.x
PING x.x.x.x (x.x.x.x): 56 data bytes
64 bytes from x.x.x.x: seq=0 ttl=62 time=1.357 ms
64 bytes from x.x.x.x: seq=1 ttl=62 time=0.577 ms
^C
Installation ONIE from BIOS
Install ONIE from the BIOS using the media (usb) boot—the ONIE installer USB.
Pre-requisites
The BIOS running on your system must meet the following requirements:
•
Allows a change to the boot order so the system can boot from media (USB).
•
Allows a baud-rate change. This feature is optional; you do not need it if your BIOS is running at 115200 baud rate. The default baud rate
for ONIE is 115200.
CAUTION:
•
These procedures are for x86-based targets only, particularly targets using Rangeley or Centerton CPU-based boards.
•
Check the console (
UART-0/1
) used on the target.
•
The log messages included in this guide are subject to change.
NOTE:
The following procedure is generic and does not list a particular target. Therefore, the ONIE images are
specified
using
the
<platform>_<cpu>
notation. For example, the ONIE media (usb) iso image is
onie-recovery-x86_64-
dell_<platform>_<cpu>-r0.iso
.
12
ONIE installation instructions