Dell PowerSwitch S5212F-ON S5200-ON Series BMC User Guide March 2019 - Page 21

Parameter, Parameter data, Data 1:-Protocol TCP/UDP

Get Dell PowerSwitch S5212F-ON PDF manuals and user guides View all Dell PowerSwitch S5212F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Parameter # Add the IPv4 port number rule 2 Add the Pv4 port number range rule 3 Remove the IPv4 address rule 4 Remove the range of IPv4 addresses rule 5 Parameter data [5:8]-Ending IP address until IPs are blocked or unblocked based on the state. For example, if the IP address is x1.x2.x3.x4, the format is: 1st byte = x1 2nd byte = x2 3rd byte = x3 4th byte = x4 Data 1:-Protocol TCP/UDP 0 = TCP 1 = UDP 2 = both TCP and UDP Data 2:3-port number [2:3]-MX byte first. Port number blocked or unblocked based on the state. Data 1:-Protocol TCP/UDP 0 = TCP 1 = UDP 2 = both TCP and UDP Data 2:5-port range [2:3]-Port number from the ports blocked or unblocked based on the state. [4:5]-Port number till ports are blocked or unblocked based on the state. Data 1:4-IP address MS-byte first. This is the IPv4 address type that is blocked or unblocked based on state. Data 1:8-IP address range [1:4]-Starting IP address that is blocked or unblocked based on the state. [5:8]-Ending IP address that is blocked or unblocked based on the state. For example, if the IP address is x1.x2.x3.x4, the format is: 1st byte = x1 2nd byte = x2 3rd byte = x3 Configuration methods 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Parameter
#
Parameter data
[5:8]—Ending IP address until IPs are
blocked or unblocked based on the state.
For example, if the IP address is x1.x2.x3.x4,
the format is:
1st byte = x1
2nd byte = x2
3rd byte = x3
4th byte = x4
Add the IPv4 port number rule
2
Data 1:—Protocol TCP/UDP
0 = TCP
1 = UDP
2 = both TCP and UDP
Data 2:3—port number
[2:3]—MX byte
first.
Port number blocked
or unblocked based on the state.
Add the Pv4 port number range rule
3
Data 1:—Protocol TCP/UDP
0 = TCP
1 = UDP
2 = both TCP and UDP
Data 2:5—port range
[2:3]—Port number from the ports blocked
or unblocked based on the state.
[4:5]—Port number till ports are blocked or
unblocked based on the state.
Remove the IPv4 address rule
4
Data 1:4—IP address
MS-byte
first.
This is the IPv4 address type
that is blocked or unblocked based on state.
Remove the range of IPv4 addresses rule
5
Data 1:8—IP address range
[1:4]—Starting IP address that is blocked or
unblocked based on the state.
[5:8]—Ending IP address that is blocked or
unblocked based on the state.
For example, if the IP address is x1.x2.x3.x4,
the format is:
1st byte = x1
2nd byte = x2
3rd byte = x3
Configuration
methods
21