Dell PowerVault 110T LTO3 User Guide - Page 29

Loading a Tape Cartridge, Unloading a Tape Cartridge, Setting the Write-Protect Switch on Tape - lto 3

Get Dell PowerVault 110T LTO3 PDF manuals and user guides View all Dell PowerVault 110T LTO3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

1. LTO cartridge memory 2. Label area 3. Write-protect switch 4. Insertion guide 5. Cartridge door 6. Leader pin Loading a Tape Cartridge 1. Ensure that the tape drive is powered on (the status light is solid green). 2. Ensure that the write-protect switch (see number 3 in Figure 4)) is properly set. (See "Setting the Write-Protect Switch on Cartridges"). 3. Grasp the cartridge so that the write-protect switch faces you. 4. Slide the cartridge into the tape load compartment (see Figure 4). ¡ If the cartridge is already in the ejected position and you want to reinsert it, remove the cartridge and then insert it again. ¡ If the cartridge is already loaded and you cycle the power (turn it off, then on), the tape will reload. Figure 4. Loading Unloading a Tape Cartridge 1. Ensure that the tape drive is powered on (the status light is solid green). 2. Press the eject button (see number 1 in Figure 2). The drive rewinds the tape and partially ejects the cartridge. The status light flashes green while the tape rewinds, then goes out before the cartridge partially ejects. 3. After the cartridge partially ejects, grasp the cartridge and remove it. Whenever you unload a tape cartridge, the tape drive writes any pertinent information to the cartridge memory. NOTICE: Do not remove a tape cartridge while the drive activity indicator is on. Setting the Write-Protect Switch on Tape Cartridges NOTICE: Write-protection will not prevent a cartridge from being erased by bulk-erasure or degaussing. Do not bulk erase Ultrium format cartridges. This will destroy prerecorded servo information and render the cartridge unusable. Always use the long or quick erase command in your backup software to erase cartridges. The position of the write-protect switch (number 1 in Figure 5) on the tape cartridge determines whether you can write to the tape: l If the switch is set to locked (locked padlock), data cannot be written to the tape. l If the switch is set to unlocked (unlocked padlock or black void), data can be written to the tape. Figure 5. Setting the Write-Protect Switch

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
1.
LTO cartridge memory
2.
Label area
3.
Write-protect switch
4.
Insertion guide
5.
Cartridge door
6.
Leader pin
Loading a Tape Cartridge
1.
Ensure that the tape drive is powered on (the status light is solid green).
2.
Ensure that the write-protect switch (see number 3 in
Figure 4)
) is properly set. (See "
Setting the Write
-
Protect Switch on Cartridges
").
3.
Grasp the cartridge so that the write-protect switch faces you.
4.
Slide the cartridge into the tape load compartment (see Figure 4).
¡
If the cartridge is already in the ejected position and you want to reinsert it, remove the cartridge and then insert it again.
¡
If the cartridge is already loaded and you cycle the power (turn it off, then on), the tape will reload.
Figure 4. Loading
Unloading a Tape Cartridge
1.
Ensure that the tape drive is powered on (the status light is solid green).
2.
Press the eject button (see number 1 in
Figure 2
). The drive rewinds the tape and partially ejects the cartridge. The status light flashes green while the
tape rewinds, then goes out before the cartridge partially ejects.
3.
After the cartridge partially ejects, grasp the cartridge and remove it.
Whenever you unload a tape cartridge, the tape drive writes any pertinent information to the cartridge memory.
Setting the Write-Protect Switch on Tape Cartridges
The position of the write-protect switch (number 1 in
Figure 5
) on the tape cartridge determines whether you can write to the tape:
l
If the switch is set to locked (locked padlock), data cannot be written to the tape.
l
If the switch is set to unlocked (unlocked padlock or black void), data can be written to the tape.
Figure 5. Setting the Write-Protect Switch
NOTICE: Do not remove a tape cartridge while the drive activity indicator is on.
NOTICE: Write-protection will not prevent a cartridge from being erased by bulk-erasure or degaussing. Do not bulk erase Ultrium format cartridges.
This will destroy prerecorded servo information and render the cartridge unusable. Always use the long or quick erase command in your backup
software to erase cartridges.