Dell W-7030 Controller Installation Guide - Page 24

FCC, Industry Canada, EU Regulatory Conformance, This product complies with 21 CFR

Page 24 highlights

CAUTION: Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure. This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC 60825-2: 2000. For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors should be installed in the product. CAUTION: Although this controller has been tested up to 1kV per CE immunity requirements, this product requires surge protection to be provided as part of the building installation to protect against unidirectional surges resulting from electrical switching and lightning strikes. For protection against these surges in an outdoor installation, any exposed wiring must be shielded, and the shield for the wiring must be grounded at both ends. FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be require to correct the interference at their own expense. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of the Department of Communications. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: "Appareils Numériques," NMB-003 édictée par le ministère des Communications. EU Regulatory Conformance This product is CE marked according to the provisions of the EMC Directive (2004/108/EC) - CE. Dell hereby declares that W-7030 controller device models are in compliance with the essential requirements and other relevant provisions of Directive (2004/108/EC). CE The Declaration of Conformity made under Directive 1999/5/EC is available for viewing on dell.com. 24 | Specifications, Safety, and Compliance Dell Networking W-7030 Controller | Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

24
|
Specifications, Safety, and Compliance
Dell Networking W-7030 Controller
| Installation Guide
This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2:
2001, IEC 60825-2: 2000.
For continued compliance with the above laser safety standards, only approved Class 1 modules from our
approved vendors should be installed in the product.
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be require to correct the interference at their own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set
out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department
of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de
Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le
ministère des Communications.
EU Regulatory Conformance
This product is CE marked according to the provisions of the EMC Directive (2004/108/EC) - CE.
Dell hereby declares that W-7030 controller device models are in compliance with the essential requirements and
other relevant provisions of Directive (2004/108/EC). CE The Declaration of Conformity made under Directive
1999/5/EC is available for viewing on
dell.com.
CAUTION:
Use of controls or adjustments of performance or procedures other than those specified in this manual may result in
hazardous radiation exposure.
CAUTION:
Although this controller has been tested up to 1kV per CE immunity requirements, this product requires surge
protection to be provided as part of the building installation to protect against unidirectional surges resulting from electrical
switching and lightning strikes.
For protection against these surges in an outdoor installation, any exposed wiring must be shielded, and the shield for the wiring
must be grounded at both ends.