Denon AVD-2000 Operating Instructions - Page 27
Troubleshooting
View all Denon AVD-2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
ENGLISH 13 TROUBLESHOOTING If a problem should arise, first check the following: 1. Are the connections correct? 2. Have you operated the receiver according to the Operating Instructions? 3. Are the speakers, turntable, and other components operating properly? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction, Disconnect the power immediately and contact your store of purchase. Common problems arising when listening to the CD. records, tapes, and FM broadcasts, etc. Symptom DISPLAY not lit and sound not produced when power switch set to on. DISPLAY lit but sound not produced. DISPLAY is not displayed. Cause • Power cord not plugged in securely. • Output cords not securely connected. • Improper position of the input selection button. • Volume control set to minimum. • Digital signals not input Digital input se- lected. • Surround mode of AV receiver con- nected to AVD-2000 not set to "6CH EX. IN", • "DISPLAY" set to "Display off". Measures • Check the insertion of the power cord plug. • Connect securely. • Sei to a suitable position. • Turn volume up to suitable level. • Input digital signals or select input jacks to which digital signals are being input. • Set the AV receiver's surround mode to "6CH EX. IN". • Set the dimmer to an appropriate position. Page 7 6 16 16 16 - 19 16 14 Remote control unit Sound produced only from one chan- • Incomplete connection of input/output • Connect securely. 6, 7 nel. cords. Positions of instruments reversed dur- • Reverse connections of left and right • Check left and right connections. 6, 7 ing stereo playback. input/ output cords. i This unit does not operate properly • Batteries dead. • Replace with new batteries. 26 when remote control unit is used. • Remote control unit too far from this unit. • Move closer. 26 • Obstacle between this unit and remote • Remove obstacle. 26 control unit. • Different button is being pressed. • Press the proper button. - • El) and 6 ends of battery inserted in re- • Insert batteries properly. 26 verse. 14 SPECIFICATIONS • D/A output (REG OUT) Rated output: Total harmonic distortion: S/N ratio: Dynamic range: Frequency response: 2 V (at 0 dB playback) 0.005% (1 kHz, at 0 dB) 110dB 105dB 10 - 20 kHz: +0, -3 dB (at LARGE mode) • OUTPUT Frequency response: FRONT, CENTER: SURROUND: SUBWOOFER: (at LARGE mode) t SMALL mode) 20 -'20 kHz: + 0, -3 dB 80 - 20 kHz: + 0, - 3 dB 80 ,- 20 kHz: +0, -3 dB 20 - 80 Hz: +0, -3 dB • INPUT format AC-3RF: AC-3RF interface format Digital input (COAXIAL-1, COAXIAL-2, OPTICAL-1, OPTICAL-2): Digital audio interface (DOLBY DIGITAL, PCM formatted) 6CH EXT.IN: Input sensitivity: 200 mV • General Power supply: Power consumption: Maximum external dimensions: Weight: AC 120 V, 60 Hz 27 W 434 (WI x 75 (H) x 238 (D) mm (17-3/32" (w) x 2-61/64" (H) x 9-3/8" (DI) 3.6 kg (7 lbs 15 oz) • Remote control unit (RC-838) Batteries: External dimensions: Weight: R6P/AA Type (two batteries) 44 (W) x 155 (H) x 29 (D) mm (1-47/64" (w) x 6-7/64" (H) x 1-9/64" (DI) 90 g (Approx 3 oz) (including batteries) 27