Dewalt DCN21PLM1 Instruction Manual - Page 11
Storage Recommendations, COMPONENTS FIG. A, OPERATION, Installing and Removing the Battery Pack, Fig - framing nailer
![]() |
View all Dewalt DCN21PLM1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights; c. Move the charger and battery pack to a location where the surrounding air temperature is approximately 65 °F - 75 °F (18 ° - 24 °C); d. If charging problems persist, take the tool, battery pack and charger to your local service center. 4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse effect on the battery pack. 5. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug the charger before attempting to clean. 6. Do not freeze or immerse the charger in water or any other liquid. Storage Recommendations 1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold. 2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place out of the charger for optimal results. NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use. SAVE THESE INSTRUCTIONS FOR FUTURE USE COMPONENTS (FIG. A) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. Refer to Figure A at the beginning of this manual for a complete list of components. Intended Use The DCN21PL cordless framing nailer has been designed for driving nails into wooden workpieces. DO NOT use under wet conditions or in presence of flammable liquids or gases. This cordless framing nailer is a professional power tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. NOTICE: NEVER spray or in any other way apply lubricants or cleaning solvents inside the tool. This can seriously affect the life and performance of the tool. English TOOL SPECIFICATIONS Firing mode Selective: Bump or Sequential Voltage 20 Height 16.5" (419 mm) Width 4" (104 mm) Length 13.25" (335 mm) Weight 8.5 lbs (3.85 kg) Magazine angle 21° Loading capacity Up to 49 nails NAIL SPECIFICATIONS Full Round Head Nail lengths 2" - 3-1/4" (50 mm - 83 mm) Shank diameters 0.113" - 0.148" (2.8 mm - 3.3 mm) Nail stick angles 21° Shank types Smooth and Ring OPERATION WARNING: Always wear safety glasses to protect your eyes from flying construction debris. An optional debris cover is available as an accesory to help reduce contruction debris and collation material. WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. Installing and Removing the Battery Pack (Fig. D) NOTE: For best results, make sure your battery pack is fully charged. To install the battery pack 12 into the tool handle, align the battery pack with the rails inside the tool's handle and slide it into the handle until the battery pack is firmly seated in the tool and ensure that it does not disengage. To remove the battery pack from the tool, press the release button 25 and firmly pull the battery pack out of the tool handle. Insert it into the charger as described in the charger section of this manual. 9
![](/manual_guide/products/dewalt-dcn21plm1-instruction-manual-c5463c3/11.png)