Dewalt DCT419S1 Instruction Manual - Page 20

MAINTENANCE, Cleaning, Troubleshooting - review

Get Dewalt DCT419S1 PDF manuals and user guides View all Dewalt DCT419S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

English MAINTENANCE Cleaning WARNING: Blow dirt and dust off with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. CHARGER CLEANING INSTRUCTIONS WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Troubleshooting SITUATION Unit does not turn on PROBABLE CAUSE • No power to unit SOLUTION • Make sure 12V Max* battery pack is fully charged • Fully seat the 12V Max* battery pack in the handle Unit does not display embedded materials; says "Pre-Scan Data Mapping" • Unit is in process of mapping scanned area • Review the Scanning Process section of the manual SITUATION Frequently getting "Lost Contact" error No embedded materials detected or difficulty in detecting embedded materials Difficulty in detection of metal PROBABLE CAUSE • Need to re-initialize • Too narrow of area mapped • Difficulty in scanning below special wall condition • Metal items too deep SOLUTION • Remove unit from the wall. When the "Begin Scanning" screen appears, press the OK button (I). Ensure that the unit is off of the wall surface and that there is nothing such as a hand or other object on the back surface. Press the OK button (I) to complete the initialization process. • Re-map larger area • Scan slowly • Scan in a straight line • Review the Detection through Special Surface Conditions section of the manual • Scan in both the horizontal and vertical directions • Ensure that the unit is at least 6" (150 mm) away from the wall when powering on • Scan in both horizontal and vertical straight lines. Metal sensitivity is increased when the metal object is parallel to the sensor. NOTE: The metal sensing is located at the bottom of the unit. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
18
English
MAINTENANCE
Cleaning
WARNING:
Blow dirt and dust off with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear ANSI Z87.1
approved eye protection when performing this.
WARNING:
Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING:
Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaning solutions.
Troubleshooting
SITUATION
PROBABLE CAUSE
SOLUTION
Unit does not
turn on
• No power to unit
• Make sure 12V Max*
battery pack is fully
charged
• Fully seat the 12V Max*
battery pack in the handle
Unit does not
display embedded
materials; says
"Pre-Scan Data
Mapping"
• Unit is in process of
mapping scanned
area
• Review the
Scanning
Process
section of the
manual
SITUATION
PROBABLE CAUSE
SOLUTION
Frequently getting
"Lost Contact"
error
• Need to re-initialize
• Remove unit from the
wall. When the "Begin
Scanning" screen
appears, press the OK
button (I). Ensure that
the unit is off of the wall
surface and that there is
nothing such as a hand or
other object on the back
surface. Press the OK
button (I) to complete the
initialization process.
No embedded
materials detected
or difficulty
in detecting
embedded
materials
• Too narrow of area
mapped
• Difficulty in scanning
below special wall
condition
• Re-map larger area
• Scan slowly
• Scan in a straight line
• Review the
Detection
through Special Surface
Conditions
section of the
manual
• Scan in both the horizontal
and vertical directions
• Ensure that the unit is
at least 6" (150 mm)
away from the wall when
powering on
Difficulty in
detection of metal
• Metal items too
deep
• Scan in both horizontal
and vertical straight
lines. Metal sensitivity is
increased when the metal
object is parallel to the
sensor.
NOTE:
The metal
sensing is located at the
bottom of the unit.