Home » Epson Manuals » Inkjet Printers » Epson 4000 » Manual Viewer

Epson 4000 Service Manual - Page 158

Troubleshooting, Troubleshooting Based on Panel Messages

UPC - 010343848337

Add to My Manuals
Save this manual to your list of manuals

Page 158 highlights

EPSON Stylus Pro 4000 Revision B Priority LCD Panel Message FORBIDDEN MEDIA FROM P. TRAY FEED SHEET PAPER MANUARY INK OUT INVALID INK CRTG WRONG INK CRTG SET INK CRTG NO INK CRTG MNT TNK FULL LOWER INK LEVERS LOWER L INK LVR LOWER R INK LVR TOP COVER OPEN LOAD PAPER LOAD PAPER SUCTION SET PAPER LEVER PAPER JAM NO MNT TNK REAR COVER OPEN OPTION I/F ERROR UNLOCK PRINT HEAD Table 3-1. Displayed Error Messages Displayed Error Paper Check ASF prohibitions *5 ON Ink out *1 GENUINE error, Wrong model number *1 Wrong dye/pigment, Wrong destination, Wrong 4-color/8-color*1 Ink Cartridge failure *1 No Ink Cartridge*1 Maintenance Tank full Releasing left and right ink lever Releasing left ink lever Releasing right ink lever Printer Cover open Releasing Paper Lever (Except roll paper) Releasing Paper Lever (Roll paper only) Releasing Paper Lever in operation Paper jam No Maintenance Tank Rear Cover open Type-B Option I/F Card Error CR lock unlocked error - - - ON ON ON Blink - - Blink Blink LED Pause - - ON - - - - - - Blink Blink Ink Check - ON ON ON ON ON ON - - - - - - - - ON - Blink Blink Reference Page p.167 p.167 p.167 p.167 p.167 p.168 p.168 p.168 p.168 p.168 p.168 p.169 p.169 p.169 p.170 p.170 p.170 p.170 p.171 High SERVICE REQ. nnnnnnnnn Service request, CR servo error (fatal error) Blink Blink Blink Refer to Table3-2 Note "*1": Blink correspond ink indicator. However, wrong ink set configuration in Initial Ink Charge and filling up ink when replacing ink condition end up blinking as follows. When Matte Black is installed in 1st row of ink set configuration and Matte Black or Photo Black is installed in 5th row, indicator (6, 7, 8th row) will blink as an error. "*2": Paper check LED flashes at 5-second intervals. "*3": To promote that release is available by [Pause] key, display the following display by turns at 1 sec., intervals. "PRESS PAUSE BUTTON" "*4": Received data is initialized without initializing mechanisms (including completion of forced cleaning) even if panel reset has been done. "*5": Display by switching at 3-second intervals. Troubleshooting Troubleshooting Based on Panel Messages 158

Section	Page
EPSON Stylus Pro 4000	1
Product Description	9
1.1 Product Description	10
1.1.1 Features	10
1.2 Basic Specifications	12
1.2.1 Print Specifications	12
1.2.2 Character Specification	12
1.2.3 Control Code	12
1.2.4 Paper Feed Specification	13
1.2.5 Paper Feeder Specification	13
1.2.6 Paper Specification	14
1.2.6.1 Roll Paper	14
1.2.6.2 Cut Sheet	15
1.2.6.3 Special Paper	16
1.2.7 Mechanism Specifications	18
1.2.7.1 Printable Area	18
1.2.7.2 Borderless Print Specification	19
1.2.7.3 Paper Set Lever	20
1.2.7.4 Cut Specification	20
1.2.8 Electrical Specification	21
1.2.9 Reliability	22
1.2.10 Environmental Conditions	22
1.2.10.1 Temperature/Humidity	22
1.2.10.2 Vibration	23
1.2.10.3 Shock	23
1.2.10.4 Surrounding Space	23
1.2.11 Overall Dimensions	24
1.2.12 Accessories	25
1.3 External View and Parts Names	26
1.4 Operating Panel	27
1.4.1 Buttons and Functions	27
1.4.1.1 LED	27
1.4.1.2 Switch	28
1.4.2 Panel Display	30
1.4.2.1 Panel Display in Operation (LCD and LED Display)	30
1.4.2.2 Paper Type Icon Display	35
1.4.2.3 PG Setting Display	35
1.4.2.4 Ink Remaining Indicator Display	35
1.4.2.5 Suction Adjustment and Indicator Display	35
1.4.3 Job information	36
1.4.4 Panel Setting	37
1.4.4.1 Outline	37
1.4.4.2 Panel Setting Menu Item	41
1.4.4.3 PG Setting	45
1.4.4.4 Page Lines	46
1.4.4.5 Interface Select	46
1.4.4.6 Code Page Switching	46
1.4.4.7 Roll Paper Margin	47
1.4.4.8 Paper Width Detection	48
1.4.4.9 Skew Error Detection	49
1.4.4.10 Job Time-out Setting	49
1.4.4.11 Cutter Position Adjustment	50
1.4.4.12 Auto Margin Refresh	51
1.4.4.13 Cut Sheet Size Error	51
1.4.4.14 Auto Nozzle Check for Each Job	52
1.4.4.15 Cleaning Setting for Nozzle Check	52
1.4.4.16 Super Low Speed Cut Mode	53
1.4.4.17 Printer Setup Value Initialization	53
1.4.4.18 Nozzle Check Pattern Printing	54
1.4.4.19 Status Printing	55
1.4.4.20 Job Information Print	57
1.4.4.21 User Paper Setting Printing	58
1.4.4.22 Firmware Version	59
1.4.4.23 Printable Pages per Ink Cartridge	59
1.4.4.24 Ink Remaining	60
1.4.4.25 Maintenance Tank Count	61
1.4.4.26 Consumption Counter	61
1.4.4.27 Clear consumption counter	61
1.4.4.28 Job History Display	61
1.4.4.29 Clear Job History	61
1.4.4.30 Total Print Pages	61
1.4.4.31 Consumable Life	62
1.4.4.32 User Paper Setting	64
1.4.4.33 Cutter Blade Replacement	69
1.4.4.34 Ink Replacement Method (8-color, 4-color)	69
1.4.4.35 Power Cleaning	69
1.4.4.36 Date Setting	69
1.4.4.37 Gap Adjustment (Bi-D Adjustment, Uni-D Adjustment)	69
1.4.5 Maintenance Mode 1	73
1.4.6 Maintenance Mode 2	79
1.4.6.1 Self Testing Menu (SELF TESTING)	80
1.4.6.2 Adjustment Setting Menu (SERVICE CONFIG)	89
1.4.6.3 Counter Display Menu (VIEW COUNTERS)	90
1.4.6.4 Counter Initialization Menu (CLEAR COUNTERS)	91
1.4.6.5 Maintenance Information Menu (MAINT INFO)	93
1.4.6.6 Maintenance Information Initialization Menu (INIT INFO)	104
1.4.6.7 Parameter Backup Mode Menu (PARAMETER BACKUP MODE)	104
1.4.7 MIB Function	105
1.4.8 Function to Prevent Irregular Printing	105
1.4.9 Initialization	106
1.4.9.1 Hardware Initialization	106
1.4.9.2 Software Initialization	106
1.4.9.3 Panel Initialization	106
1.4.10 Default Setup Values	106
1.4.10.1 Operation Default Setting	106
1.5 Controller	107
1.6 Interface	108
1.6.1 USB interface	108
1.6.2 IEEE1394 Interface	109
1.6.3 Optional Interface	110
1.6.4 Supplements	112
1.7 Optional Units and Consumables	113
1.7.1 Ink Cartridge	113
1.7.2 Cleaning cartridge	114
1.7.3 Maintenance Tank	114
Operating Principles	115
2.1 Overview	116
2.2 Printer Mechanism Components	117
2.2.1 Printing Mechanism (Print Head)	118
2.2.2 Ink Supply Mechanism	119
2.2.3 Cleaning Mechanism	121
2.2.4 Carriage (CR) Mechanism	126
2.2.4.1 Carriage Unit Movement Components	127
2.2.4.2 Platen Gap Adjustment Components	129
2.2.4.3 Cutter Solenoid/CR Lock Mechanism	132
2.2.5 Paper Feed Mechanism	132
2.2.5.1 ASF Paper Feed Mechanism	135
2.2.6 Paper Eject/Release Mechanism	141
2.2.6.1 Paper Eject Mechanism	141
2.2.6.2 Release Mechanism	144
2.2.7 Multi Sensor	146
2.2.7.1 Overview	146
2.2.7.2 Operations/Functions	147
2.2.8 Others	152
2.3 Outline of Control Circuit Board	153
2.4 Outline of Power Supply Circuit Board	154
Troubleshooting	155
3.1 Outline	156
3.1.1 Check Before Troubleshooting	156
3.1.2 Narrow Down the Trouble	156
3.2 Troubleshooting Based on Panel Messages	157
3.2.1 Message Table	157
3.2.2 Corrective Actions for Displayed Warnings	160
3.2.3 Corrective Actions for Error Display	163
3.2.4 Corrective Actions for Service Request Display	172
3.3 Troubleshooting Based on Your Printout	192
Disassembly & Assembly	196
4.1 Introductory Information	197
4.1.1 Cautions	197
4.1.2 Tools	199
4.1.3 Screws	200
4.2 Disassembly Procedures	201
4.2.1 Basic Operations	202
4.2.1.1 Release of the Transport Retaining Lever	202
4.2.1.2 Carriage Unit Lock Release/Lock Set Method	203
4.2.2 Consumable Parts/ASF Cassette Removal	204
4.2.2.1 Ink Cartridges	204
4.2.2.2 Maintenance Tank (Porous Pad Assy., Ink Eject)	205
4.2.2.3 Cutter Assembly	206
4.2.2.4 ASF Cassette	207
4.2.2.5 Spindle	208
4.2.3 Panel Unit/Housing Removal	209
4.2.3.1 Holder, Roller, Unit	209
4.2.3.2 Paper Guide Assy., M, SP	210
4.2.3.3 Cover, Side, Left	211
4.2.3.4 Cover, Side, Right	212
4.2.3.5 Panel, Front/Panel Unit	214
4.2.3.6 Cover, Printer	216
4.2.3.7 Cover, Rear	218
4.2.3.8 P Cover Open Sensor	219
4.2.3.9 Rear Cover Sensor	220
4.2.4 Circuit Board Removal	221
4.2.4.1 C511 MAIN Board	221
4.2.4.2 Power Supply Board	228
4.2.4.3 C511_SUB Board	229
4.2.4.4 C511_SUB-B Board	231
4.2.4.5 C511_SUB-C Board	233
4.2.5 Printer Mechanism Disassembly	235
4.2.5.1 Printer Mechanism (SP)	236
4.2.5.2 Fan, Blower	238
4.2.6 ASF	240
4.2.6.1 ASF Unit	240
4.2.6.2 Roller Assy., LD, Left / Roller Assy., LD, Right	248
4.2.6.3 Mount Assy., Plate, Motor, ASF, SP	253
4.2.6.4 ASF Phase Sensor	257
4.2.6.5 ASF Paper Sensor	259
4.2.7 Carriage Mechanism	260
4.2.7.1 Carriage Unit	260
4.2.7.2 Motor Assy., CR	264
4.2.7.3 Motor Assy., PG	267
4.2.7.4 CR_HP Sensor	269
4.2.7.5 Multi Sensor	270
4.2.7.6 PG Phase Sensor	271
4.2.7.7 CR Encoder Sensor	273
4.2.7.8 Scale, CR	274
4.2.7.9 Pulley, Driven/Shaft, Pulley	275
4.2.7.10 Solenoid, CR	277
4.2.8 Ink System	278
4.2.8.1 Printhead	278
4.2.8.2 Valve Assy., Head	284
4.2.8.3 Gutter, Ink	287
4.2.8.4 I/H Left Unit / I/H Lever Sensor (Left)	289
4.2.8.5 I/H Right Unit / I/H Lever Sensor (Right)	298
4.2.8.6 Box Assy., Flushing / Pump Unit	309
4.2.8.7 Guide, Waste Ink	315
4.2.8.8 Pump Phase Sensor	316
4.2.8.9 Holder, FFC	318
4.2.8.10 Holder, FFC; B	321
4.2.8.11 Harness, Head, Intermit / Harness, Head	324
4.2.8.12 Tube, Supply, Ink (Y/M/C/MK) on the Left Side of the Main Unit	327
4.2.8.13 Tube, Supply, Ink (LK(Y)/LM(M)/LC(C)/PK(MK)) on the Right side of the Main Unit	331
4.2.9 Paper Feed Mechanism	335
4.2.9.1 Release Unit	335
4.2.9.2 Paper Eject Unit	340
4.2.9.3 Motor Assy., PF	341
4.2.9.4 P_THICK Sensor (0.8) / P_THICK Sensor (0.3)	343
4.2.9.5 PE Sensor	344
4.2.9.6 Rear Manual Insertion Sensor	346
4.2.9.7 Paper Eject Phase Sensor	348
4.2.9.8 Paper Eject Release Sensor	348
4.2.9.9 PF Encoder Sensor	349
4.2.10 Harness Routing	350
4.2.10.1 Harnesses on Left Side of Printer	350
4.2.10.2 Harnesses on Right Side of Printer	352
Adjustment	354
5.1 Overview	355
5.1.1 Cautions	355
5.1.2 Advance of Adjustment	355
5.1.3 The Part/Unit that is required Adjustment	355
5.1.4 Adjustment Items classified by Part/Unit	356
5.1.5 Adjustment Item	358
5.1.6 Adjustment Tools	361
5.1.7 Adjustment Program Basic Operation	362
5.2 Mechanical Adjustment	363
5.2.1 CR Timing Belt Tension Adjustment	363
5.2.2 PF Timing Belt Tension Adjustment	365
5.2.3 Paper Thickness Sensor Adjustment	367
5.2.4 CR Encoder Sensor Position Adjustment	369
5.2.5 PG Adjustment	370
5.2.6 Multi Sensor Position Adjustment	372
5.3 Basic Adjustment	374
5.3.1 RTC&USB ID&IEEE1394 ID	374
5.3.2 Head Rank ID	375
5.3.3 Multi Sensor Level Adjustment	376
5.3.4 T&B&S (Roll Paper)	377
5.3.5 T&B&S (Cut Sheet)	379
5.3.6 Cutter Pressure Adjustment	380
5.3.7 Nozzle Bi-D Adjustment	381
5.3.8 Print Head Slant Adjustment (PF)	382
5.3.9 Print Head Slant Adjustment (CR)	384
5.3.10 Auto Uni-d Adjustment	387
5.3.11 Multi Sensor Adjustment for Auto Nozzle Check	388
5.3.12 Skew Check	390
5.3.13 Platen Position Adjustment	391
5.3.14 1000mm Feed Adjustment	393
5.3.15 Initial Ink charge flag ON/OFF	394
5.3.16 NVRAM Back Up and Write	395
5.3.17 Check Platen Gap	396
5.3.18 Ink Discharge	397
5.3.19 Initial Ink Charge	398
5.3.20 Cleaning	398
5.3.21 Rear Sensor Adjustment	399
5.3.22 Adjustment Image (for 8-color model)	400
5.3.22.1 PF Micro Feed Adjustment Bi-D	401
5.3.22.2 Dot Shift Adjustment	406
5.3.22.3 Image Print (Tanzaku)	408
5.3.23 Adjustment Image (for 4-color model)	409
5.3.23.1 4-color Dot Shift	409
5.3.23.2 Microweave Adjustment	411
5.4 Advanced Adjustment	413
5.4.1 Auto Bi-d Adjustment	413
5.4.2 Manual Bi-D Adjustment	414
5.4.3 Destination Setting	416
5.5 Check Results	417
5.5.1 Check Nozzle	417
5.5.2 Check Alignment	418
5.5.3 Print Adjustment Check Pattern	419
5.5.4 Check Cutting	420
5.6 Reset Counters	421
5.6.1 Reset Paper Ejection Switching/PG Switching Counter	421
5.6.2 Reset PF Motor Counter	421
5.6.3 Reset ASF Counter	422
5.6.4 Reset When CR Unit Change	422
5.6.5 Reset When Cleaning Unit Change	423
5.7 Installing Firmware	424
Maintenance	425
6.1 Overview	426
6.1.1 Product Life Information	427
6.1.2 Important Maintenance Items During Service Operations	427
6.2 Lubrication	428
Appendix	431
7.1 Connectors	432
7.2 Circuit Diagrams	435
7.3 Exploded Diagrams	442

Match case Limit results 1 per page

EPSON Stylus Pro 4000

Revision B

Troubleshooting

Troubleshooting Based on Panel Messages

158

Note "*1":

Blink correspond ink indicator. However, wrong ink set configuration in Initial Ink Charge and filling up ink when replacing ink condition end up blinking as follows. When

Matte Black is installed in 1st row of ink set configuration and Matte Black or Photo Black is installed in 5th row, indicator (6, 7, 8th row) will blink as an error.

"*2":

Paper check LED flashes at 5-second intervals.

"*3": To promote that release is available by [Pause] key, display the following display by turns at 1 sec., intervals.

"PRESS

PAUSE

BUTTON"

"*4": Received data is initialized without initializing mechanisms (including completion of forced cleaning) even if panel reset has been done.

"*5": Display by switching at 3-second intervals.

FORBIDDEN

MEDIA

FROM

P. TRAY

ASF prohibitions *

–

p.167

FEED

SHEET

PAPER

MANUARY

INK

OUT

Ink out *

–

p.167

INVALID

INK

CRTG

GENUINE error, Wrong model number *

–

p.167

WRONG

INK

CRTG

Wrong dye/pigment, Wrong destination,

Wrong 4-color/8-color*

–

p.167

SET

INK

CRTG

Ink Cartridge failure *

–

p.167

INK

CRTG

No Ink Cartridge*

–

p.168

MNT

TNK

FULL

Maintenance Tank full

–

p.168

LOWER

INK

LEVERS

Releasing left and right ink lever

–

p.168

LOWER

INK

LVR

Releasing left ink lever

–

p.168

LOWER

INK

LVR

Releasing right ink lever

–

p.168

TOP

COVER

OPEN

Printer Cover open

–

p.168

LOAD

PAPER

Releasing Paper Lever (Except roll paper)

–

p.169

LOAD

PAPER

SUCTION

Releasing Paper Lever (Roll paper only)

–

p.169

SET

PAPER

LEVER

Releasing Paper Lever in operation

–

p.169

PAPER

JAM

Paper jam

Blink

–

p.170

MNT

TNK

No Maintenance Tank

–

p.170

REAR

COVER

OPEN

Rear Cover open

–

p.170

OPTION

I/F

ERROR

Type-B Option I/F Card Error

Blink

p.170

UNLOCK

PRINT HEAD

CR lock unlocked error

Blink

p.171

High

SERVICE

REQ.

nnnnnnnnn

Service request, CR servo error

(fatal error)

Blink

Refer to Table3-2

Table 3-1.

Displayed Error Messages

Priority

LCD Panel Message

Displayed Error

LED

Reference Page

Paper Check

Pause

Ink Check