Epson ActionNote 4000 User Manual - Page 29

Starting the SETUP Program, Press Delete to run SETUP

Get Epson ActionNote 4000 PDF manuals and user guides View all Epson ActionNote 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

The configuration you define through SETUP is stored in a special area of memory called CMOS RAM. This memory is backed up by a battery, so it is not erased when you turn off or reset the computer. Whenever you start the computer it checks the settings, and if it discovers a difference between the information in CMOS RAM and your system's configuration, it prompts you to run SETUP. You see a message such as the following: CMOS memory mismatch Run SETUP You also see the following prompt at the bottom of the screen: Press F1 to continue or Delete to run SETUP If this happens, press setting. to run SETUP and correct the Starting the SETUP Program To start SETUP, make sure there is no diskette in the diskette drive; then turn on your computer. (If your computer is already on, turn it off, wait 20 seconds, and then turn it on again.) After the self test, you see the following prompt at the bottom of the screen: Press Delete to run SETUP As soon as you see this message, press If you do not press within approximately five seconds, the computer starts loading the operating system and you will not be able to run SETUP. If this happens, restart or reset the computer and try again. 2-2 Running SETUP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
The configuration you define through SETUP is stored in a
special area of memory called CMOS RAM. This memory is
backed up by a battery, so it is not erased when you turn off or
reset the computer. Whenever you start the computer it checks
the settings, and if it discovers a difference between the
information in CMOS RAM and your system’s configuration, it
prompts you to run SETUP. You see a message such as the
following:
CMOS memory mismatch
Run SETUP
You also see the following prompt at the bottom of the screen:
Press F1 to continue or Delete to run SETUP
If
this happens,
press
to run SETUP and correct the
setting.
Starting the SETUP Program
To start SETUP, make sure there is no diskette in the diskette
drive; then turn on your computer. (If your computer is already
on, turn it off, wait 20 seconds, and then turn it on again.) After
the self test, you see the following prompt at the bottom of the
screen:
Press Delete to run SETUP
As
soon
as you see
this message,
press
If you do not press
within approximately five seconds,
the computer starts loading the operating system and you will
not be able to run SETUP. If this happens, restart or reset the
computer and try again.
2-2 Running SETUP