Epson ActionNote 4000 User Manual - Page 42

Saving Your Settings and Exiting Setup, PRESS F5 TO, AND EXIT, PRESS F1 TO EXIT

Get Epson ActionNote 4000 PDF manuals and user guides View all Epson ActionNote 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Saving Your Settings and Exiting SETUP When you leave the SETUP program, you can choose to either save the settings you have changed or exit the program without saving any changes. Follow these steps: 1. Press You see the following prompt: PRESS F5 TO SAVE AND EXIT PRESS F1 TO EXIT W/O SAVE 2. If you want to save your changes, press I f you don't want to save your changes, press Either way, the system reboots. 3. If you have just run SETUP for the first time, see "Post-SETUP Procedures," below. Note You may see an error message and a prompt to run SETUP when your computer is rebooting if it detects a problem in your SETUP configuration. If so, follow the instructions on the screen to run SETUP and correct the problem. You may also see an error message if you have not installed your operating system on the hard disk and you have not inserted a system diskette in drive A. If you receive this error message, follow the instructions in your operating system manual to install the software. Running SETUP 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Saving Your Settings and Exiting SETUP
When you leave the SETUP program, you can choose to either
save the settings you have changed or exit the program without
saving any changes.
Follow these steps:
1.
Press
You
see
the
following
prompt:
PRESS F5 TO
SAVE
AND EXIT
PRESS F1 TO EXIT
W/O SAVE
2.
If you want to save your changes,
press
I f you don’t
want to save your changes, press
Either
way, the
system reboots.
3.
If you have just run SETUP for the first time, see “Post-SETUP
Procedures,” below.
Note
You may see an error message and a prompt to run SETUP
when your computer is rebooting if it detects a problem in
your SETUP configuration. If so, follow the instructions on
the screen to run SETUP and correct the problem.
You may also see an error message if you have not installed
your operating system on the hard disk and you have not
inserted a system diskette in drive A. If you receive this error
message, follow the instructions in your operating system
manual to install the software.
Running SETUP 2-15