Epson ActionNote 880C User Manual - Page 53

Using Your Computer, Both of these drivers are loaded in your computer's

Get Epson ActionNote 880C PDF manuals and user guides View all Epson ActionNote 880C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Note If you are using an ATA hard disk or ATA flash card, make sure your CONFIG.SYS file contains this command: DEVICEHIGH=C:\CARDSOFT\ATADRV.EXE If you are using an SRAM card, make sure the CONFIG.SYS file contains this command: DEVICEHIGH=C:\CARDSOFT\MTSRAM.EXE Both of these drivers are loaded in your computer's CONFIG.SYS file at the factory. The following table describes the removable storage card utilities. ATA utility commands Command Function ATAINIT* Partitions the ATA card and identifies its physical parameters: then you can use MS-DOS FORMAT to format the drive. ATADRV Assigns the next available drive letter to the ATA drive. When you start your system, you see a message identifying the drive letter assigned to the drives in your PCMCIA slots. MTDDRV Displays the drive letter for SRAM and ATA cards. Since these cards share drive letters, it is important to know where these cards are installed. * This command works only with ATA cards that are supported by the ATADRV driver. 2-18 Using Your Computer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Note
If you are using an ATA hard disk or ATA flash card, make
sure your CONFIG.SYS file contains this command:
DEVICEHIGH=C:\CARDSOFT\ATADRV.EXE
If you are using an SRAM card, make sure the CONFIG.SYS
file contains this command:
DEVICEHIGH=C:\CARDSOFT\MTSRAM.EXE
Both of these drivers are loaded in your computer’s
CONFIG.SYS file at the factory.
The following table describes the removable storage card
utilities.
ATA
utility commands
Command
ATAINIT*
ATADRV
MTDDRV
Function
Partitions the ATA card and identifies its physical
parameters: then you can use MS-DOS FORMAT to format
the drive.
Assigns the next available drive letter to the ATA drive.
When you start your system, you see a message identifying
the drive letter assigned to the drives in your PCMCIA slots.
Displays the drive letter for SRAM and ATA cards. Since these
cards share drive letters, it is important to know where these
cards are installed.
*
This command works only with ATA cards that are supported by the
ATADRV driver.
2-18 Using Your Computer