Epson C117001-N User Manual - Page 33

Running the self test - dip switch

Get Epson C117001-N - DFX 5000+ B/W Dot-matrix Printer PDF manuals and user guides
UPC - 010343816480
View all Epson C117001-N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Running the self test The self test prints out the settings of the printer's DIP switches and the characters in the printer's memory. The test can be run in either draft,, high-speed draft, or near letter quality (NLQ) mode. Your printer's default setting is high-speed draft mode. To run the self test in high-speed draft mode, follow these steps: Caution: Always use paper that is at least 15 inches wide when running the printer's self test. 1. While holding down the LINE FEED button, turn on the printer. After printing starts, release the button. A list of your printer's settings is printed first, followed by a series of characters. Here is part of a typical self test printout in high-speed draft. 2. The self test continues until the paper runs out or until you press the ON LINE button. If the test results are satisfactory and you wish to stop the test, press the ON LINE button to take the printer off line, and then turn off the printer. 1-22 Setting Up the Printer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
Running the self test
The self test prints out the settings of the printer’s DIP switches
and the characters in the printer’s memory. The test can be run in
either draft,, high-speed draft, or near letter quality (NLQ) mode.
Your printer’s default setting is high-speed draft mode. To run the
self test in high-speed draft mode, follow these steps:
Caution:
Always use paper that is at least 15 inches wide
when running the printer’s self test.
1.
While holding down the
LINE FEED
button, turn on the printer.
After printing starts, release the button.
A list of your printer’s settings is printed first, followed by a
series of characters. Here is part of a typical self test printout
in high-speed draft.
2.
The self test continues until the paper runs out or until you
press the
ON LINE
button. If the test results are satisfactory and
you wish to stop the test, press the
ON LINE
button to take the
printer off line, and then turn off the printer.
1-22
Setting Up the Printer