Epson SureColor S30670 User Manual - Page 10

Replace with a new waste ink bottle when the level approaches the line., Waste ink tube

Get Epson SureColor S30670 PDF manuals and user guides View all Epson SureColor S30670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

5 Roll core holder locking screw The locking screws keep the roll core holders in place once they have been attached to the roll core. There are two locking screws: one on the left and one on the right. 6 Roll support Rest media temporarily on these supports when removing the take-up roll. There are two supports: one on the left and one on the right. 7 Auto switch Use this switch to select the auto take-up direction. Choose Off to disable auto take-up. 8 Manual switch Use this switch to select the manual take-up direction. The selected option takes effect when the Auto switch is in the Off position. 9 Casters There are two casters on each leg. Once installation is complete, the front casters should be kept locked while the printer is in use. 10 Airflow vents These vents vent air from inside the printer. Do not obstruct these vents. 11 Waste ink bottle (tank) holder Place the waste ink bottle in this holder. 12 Adjuster The adjusters keep the printer in place. After installing the printer, keep it securely in place during use. 13 Waste ink bottle (tank) Waste ink collects in this bottle. Replace with a new waste ink bottle when the level approaches the line. 14 Waste ink tube Waste ink is discharged from this tube. Be sure the end of this tube is in the waste ink bottle while the printer is in use. 15 Ink cartridges Install all ink cartridges into each slot. 16 Lock levers Raise the levers to unlock the ink cartridges prior to removal. Lower the levers to lock the cartridges in place after insertion. 17 Cartridge check lamp This lamp lights when an ink cartridge error occurs. On : An error occurred. Check the message on the control panel's screen. Off : No error. Introduction 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Introduction
10
5
Roll core holder locking screw
The locking screws keep the roll core holders in place once they have been attached to the roll
core. There are two locking screws: one on the left and one on the right.
6
Roll support
Rest media temporarily on these supports when removing the take-up roll. There are two supports:
one on the left and one on the right.
7
Auto switch
Use this switch to select the auto take-up direction. Choose
Off
to disable auto take-up.
8
Manual switch
Use this switch to select the manual take-up direction. The selected option takes effect when the
Auto switch is in the
Off
position.
9
Casters
There are two casters on each leg. Once installation is complete, the front casters should be kept
locked while the printer is in use.
10 Airflow vents
These vents vent air from inside the printer. Do not obstruct these vents.
11 Waste ink bottle (tank) holder
Place the waste ink bottle in this holder.
12 Adjuster
The adjusters keep the printer in place. After installing the printer, keep it securely in place during
use.
13 Waste ink bottle (tank)
Waste ink collects in this bottle.
Replace with a new waste ink bottle when the level approaches the line.
14 Waste ink tube
Waste ink is discharged from this tube. Be sure the end of this tube is in the waste ink bottle while
the printer is in use.
15 Ink cartridges
Install all ink cartridges into each slot.
16 Lock levers
Raise the levers to unlock the ink cartridges prior to removal. Lower the levers to lock the cartridges
in place after insertion.
17 Cartridge check lamp
This lamp lights when an ink cartridge error occurs.
On
:
An error occurred. Check the message on the control panel’s screen.
Off
:
No error.