Epson SureColor S50670 Setup Guide - Page 22

adjustment screw. Turn the screw counterclockwise to move the drawn line back, and turn

Get Epson SureColor S50670 PDF manuals and user guides View all Epson SureColor S50670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

20 | Adjusting the Take-in Reel 9. From the front of the printer, pull the adjustment paper taut over the platen, and check the position of the line you drew in step 7. If the line you drew is not aligned with the white line, go to step 10. If the lines are aligned, go to step 11. 10 11 10. From the front of the printer, have one person compare the line you drew in step 7 to the white line on the platen. To make adjustments, have another person at the back of the printer turn the silver adjustment screw. Turn the screw counterclockwise to move the drawn line back, and turn it clockwise to move the drawn line forward. The line will move approximately 1 mm with each turn of the screw. Continue to turn the silver adjustment screw until the drawn line reaches the front of the white line as shown.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
20
|
Adjusting the Take-in Reel
9.
From the front of the printer, pull the adjustment paper taut over the platen, and check the position of
the line you drew in step 7. If the line you drew is not aligned with the white line, go to step 10. If the
lines are aligned, go to step 11.
10.
From the front of the printer, have one person compare the line you drew in step 7 to the white line
on the platen. To make adjustments, have another person at the back of the printer turn the silver
adjustment screw. Turn the screw counterclockwise to move the drawn line back, and turn it
clockwise to move the drawn line forward. The line will move approximately 1 mm with each turn of
the screw. Continue to turn the silver adjustment screw until the drawn line reaches the front of the
white line as shown.
10
11