Home » Fujitsu Manuals » Hard Drives » Fujitsu MAJ3364MP » Manual Viewer

Fujitsu MAJ3364MP Manual/User Guide - Page 28

System Configuration

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1.3 System Configuration Figure 1.6 shows the system configuration. The IDDs are connected to the SCSI bus of host systems and are always operated as target. The IDDs perform input/output operation as specified by SCSI devices which operate as initiator. SCSI bus Figure 1.6 System configuration (1) SCSI bus configuration Up to eight SCSI devices operating as an initiator or a target can be connected to the SCSI bus for the 8-bit SCSI and up to 16 SCSI devices operating as an initiator or a target can be connected to the SCSI bus for the 16-bit SCSI in any combination. For example, the system can be configured as multi-host system on which multiple host computers that operate as initiator or connected through the SCSI bus. Using disconnect/reconnect function, concurrent input/output processing is possible on multi-SCSI devices. C141-E103-02EN 1 - 9

Section	Page
COVER	1
REVISION RECORD	2
PREFACE	6
Important Alert Items	9
MANUAL ORGANIZATION	11
CONTENTS	12
FIGURES	16
TABLES	18
CHAPTER 1 GENERAL DESCRIPTION	20
1.1 Standard Features	21
1.2 Hardware Structure	24
1.3 System Configuration	28
CHAPTER 2 SPECIFICATIONS	30
2.1 Hardware Specifications	30
2.1.1 Model name and part number	30
2.1.2 Function specifications	31
2.1.3 Environmental specifications	33
2.1.4 Error rate	34
2.1.5 Reliability	34
2.2 SCSI Function Specifications	36
CHAPTER 3 DATA FORMAT	38
3.1 Data Space	38
3.1.1 Cylinder configuration	38
3.1.2 Alternate spare area	42
3.1.3 Track format	43
3.1.4 Sector format	45
3.1.5 Format capacity	47
3.2 Logical Data Block Addressing	48
3.3 Defect Management	49
3.3.1 Defect list	49
3.3.2 Alternate block allocation	49
CHAPTER 4 INSTALLATION REQUIREMENTS	54
4.1 Mounting Requirements	54
4.1.1 External dimensions	54
4.1.2 Mounting	59
4.1.3 Notes on mounting	59
4.2 Power Supply Requirements	64
4.3 Connection Requirements	67
4.3.1 68 pin connector 16-bit SCSI model (MP model)	67
4.3.2 SCA2 type SCSI model (MC model)	75
4.3.3 Cable connector requirements	79
4.3.4 External operator panel	80
CHAPTER 5 INSTALLATION	82
5.1 Notes on Handling Drives	82
5.2 Connections	84
5.3 Setting Terminals	86
5.3.1 SCSI ID setting	87
5.3.2 Each mode setting	88
5.3.3 Mode settings	90
5.4 Mounting Drives	91
5.4.1 Check before mounting	91
5.4.2 Mounting procedures	91
5.5 Connecting Cables	92
5.6 Confirming Operations after Installation and Preparation for use	93
5.6.1 Confirming initial operations	93
5.6.2 Checking SCSI connection	94
5.6.3 Formatting	97
5.6.4 Setting parameters	99
5.7 Dismounting Drives	103
5.8 Spare Disk Drive	103
CHAPTER 6 DIAGNOSTICS AND MAINTENANCE	104
6.1 Diagnostics	104
6.1.1 Self-diagnostics	104
6.1.2 Test programs	107
6.2 Maintenance Information	108
6.2.1 Precautions	108
6.2.2 Maintenance requirements	109
6.2.3 Maintenance levels	111
6.2.4 Revision numbers	112
6.2.5 Tools and test equipment	113
6.2.6 Tests	113
6.3 Operation Check	115
6.3.1 Initial seek operation check	115
6.3.2 Operation test	115
6.3.3 Diagnostic test	115
6.4 Troubleshooting Procedures	116
6.4.1 Outline of troubleshooting procedures	116
6.4.2 Troubleshooting with disk drive replacement in the field	116
6.4.3 Troubleshooting at the repair site	118
6.4.4 Troubleshooting with parts replacement in the factory	119
6.4.5 Finding possibly faulty parts	119
CHAPTER 7 ERROR ANALYSIS	120
7.1 Error Analysis Information Collection	120
7.1.1 Sense data	120
7.1.2 Sense key, sense code, and subsense code	120
7.2 Sense Data Analysis	122
7.2.1 Error information indicated with sense data	122
7.2.2 Sense data (4-03-xx), (4-40-xx), (4-44-xx), and (4-C4-xx)	123
7.2.3 Sense data (1-1x-xx), (3-1x-xx) and (E-1D-00): Disk read error	123
7.2.4 Sense data (5-2x-xx), (5-3D-00), (5-90-00), (B-47-xx), (B-49-00), (B-4D-xx) and (B-4E-00): SCSI interface error	123
CHAPTER 8 PRINCIPLE OF OPERATION	124
8.1 Outline	124
8.2 Disk Drive Configuration	124
8.2.1 Disks	125
8.2.2 Heads	125
8.2.3 Spindle mechanism	125
8.2.4 Actuator	125
8.2.5 Air filters	125
8.3 Circuit Configuration	126
8.4 Power-On Sequence	128
8.5 Factory-Calibration	129
8.6 Read/Write Circuit	129
8.6.1 Head IC	129
8.6.2 Write circuit	130
8.6.3 Read circuit	131
8.7 Servo Control	133
8.7.1 Servo control circuit	133
8.7.2 Servo format	134
8.7.3 Servo frame format	136
8.7.4 Spindle motor control	136
8.7.5 Voice coil motor control	136
APPENDIX A LOCATIONS OF CONNECTORS AND SETTING TERMINALS	138
A.1 Locations of Connectors and Setting Terminals (MAH series MC model)	139
A.2 Locations of Connectors and Setting Terminals (MAH series MP model)	140
A.3 Locations of Connectors and Setting Terminals (MAJ series MC model)	141
A.4 Locations of Connectors and Setting Terminals (MAJ series MP model)	142
APPENDIX B SETTING TERMINALS	144
B.1 Setting Terminals	145
APPENDIX C CONNECTOR SIGNAL ALLOCATION	148
C.1 SCSI Connector Signal Allocation: SCA2 type LVD 16-bit SCSI	149
C.2 SCSI Connector Signal Allocation: 68 pin type LVD 16-bit SCSI	150
APPENDIX D MODEL NAMES AND PRODUCT NUMBERS	152
D.1 Model Names and Product Numbers	153
ADDRESSES	154