Gateway FX530S 8512279 - Gateway Computer Reference Guide (for Gateway FX-Seri - Page 51

to exit BIOS, then press

Page 51 highlights

www.gateway.com 3 Follow the anti-static precautions in "Preventing static electricity discharge" on page 48. 4 Remove the side panel by following the instructions in "Removing the side panel" on page 49. 5 Locate the jumper labeled J3C2 BIOS Config on the system board. J3C2 BIOS Config jumper J2B3 jumper (do not adjust) 6 Remove the jumper from its normal position (bridging pins 1-2), then place it in the maintenance boot position (bridging pins 2-3). 7 Reconnect the power cord. 8 Turn on your computer. The BIOS Setup utility opens. 9 Press the arrow keys to select the Performance tab. Press the arrow keys to highlight Set Processor Multiplier, then press ENTER. 10 Press the - (minus) or + (plus) key repeatedly to adjust the multiplier, then press ENTER. 11 Press F10 to exit BIOS, then press Y to accept the changes. The screen displays the message "Turn off power and reinstall the jumper in Normal mode position." 12 Turn off the computer. 13 Disconnect the power cord and follow all anti-static precautions. 14 Return the jumper to the Normal position (bridging pins 1-2). 15 Close the computer case. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160

www.gateway.com
45
3
Follow the anti-static precautions in
“Preventing static
electricity discharge” on page 48
.
4
Remove the side panel by following the instructions in
“Removing the side panel” on page 49
.
5
Locate the jumper labeled
J3C2 BIOS Config
on the
system board.
6
Remove the jumper from its normal position (bridging
pins 1-2), then place it in the maintenance boot position
(bridging pins 2-3).
7
Reconnect the power cord.
8
Turn on your computer. The BIOS Setup utility opens.
9
Press the arrow keys to select the
Performance
tab.
Press the arrow keys to highlight
Set Processor
Multiplier
, then press
E
NTER
.
10
Press the - (minus) or + (plus) key repeatedly to adjust
the multiplier, then press
E
NTER
.
11
Press
F10
to exit BIOS, then press
Y
to accept the
changes. The screen displays the message “Turn off
power and reinstall the jumper in Normal mode
position.”
12
Turn off the computer.
13
Disconnect the power cord and follow all anti-static
precautions.
14
Return the jumper to the Normal position (bridging
pins 1-2).
15
Close the computer case.
J3C2 BIOS Config
jumper
J2B3 jumper
(
do not adjust
)