Genie ProMax Stealth Owner's Manual - Page 11

Read And Follow All Safety,installation

Page 11 highlights

5. Fasten rail to power head. • • • ThsIAanicneglsirdagheedntwrpetonmsstcw[h1osreeec1urrw2tnewh]tsw,ieont[sagh6(.d2e9h)n]fo.r5altew/m1so6eo"(.f2xs)1pN/r2oo"c. k1he0et-x2sha4edxadd1le/,2r"ahilex NwtraOhveTenEl:awIsnhsneeenmrs-bsellitintdigne/gtboulipmlleoitwtsse.hrohueladdretomparinovaitdme pidr-otrpaevrel ABodljtusting 11 6. Use adjusting bolt to set chain tension (Fig. 1-4) • Cdrhaagisnosnhothueldrsaail.g slightly but not so much that it Fig. 1-4 OPEN ORANGE PARTS BAG 2... INSTALLATION : IINNISMSTTPRAOULRLCTATATIONIOTNNS WARNING sTeoverreeduincjuertyheorridsekaothf: 1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not understand an instruction, call your service representative. 2. Do Not install operator on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs and adjustments to cables, spring assembly, and other hardware must be made by a trained service person using proper tools and instructions. 3. Remove all ropes and disable all locks connected to the door before installing operator. 4. Install door operator 7 feet or more above the floor. Mount the emergency release knob 6 feet above the floor. 5. Do Not connect the operator to the source of power until instructed to do so. 6. Locate the control button: • Within sight of door. • At a minimum height of 5 feet, so small children cannot reach it. • Away from all moving parts of the door. 7. Install the entrapment WARNING label next to the wall button or console. Install the emergency release tag on, or next to, the emergency release. 8. The operator must reverse when the door contacts a 1-1/2 inch high object on the floor at the center of the doorway. This is about the size of a 2" x 4" board laid flat. FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM LWtooHofiknAdTattThthYeePindEsrtaOawlFliantDgioOsnObienRlsotDwruO.cTtYhioOenyUsteyHlolAuyVonEue?ewdhere Track Guided Doors SEE SECTION 2A CuSrveecdtioTrnacDkooHraWrdiwthare Hori1zo-PniteacleTrDaockorHWaritdhware SVCTeeuwrrcaritvtticihceokadnl (HSotrriaziognhttaTlrOacnkly) "H" "H" DOTTED LINE AT "H" INDICATES HIGHEST POINT OF TRAVEL Trackless Doors SEE SECTION 2B. Jam1b-(PTNyioepcTeeraHDcaokro)drware Pivo1t-(TPNyioepceTerHaDcaokrdo) wr are "H" "H"

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

11
1
.
READ AND FOLLOW ALL SAFETY,INSTALLATION AND
OPERATION INSTRUCTIONS. If you have any questions or
do not understand an instruction, call your service
representative.
2
.
Do Not install operator on an improperly balanced door. An
improperly balanced door could cause severe injury. Repairs
and adjustments to cables, spring assembly, and other
hardware must be made by a trained service person using
proper tools and instructions.
3
.
Remove all ropes and disable all locks connected to the
door before installing operator.
4
.
Install door operator 7 feet or more above the floor. Mount
the emergency release knob 6 feet above the floor.
5
.
Do Not connect the operator to the source of power until
instructed to do so.
6
.
Locate the control button:
Within sight of door.
At a minimum height of 5 feet, so small children cannot
reach it.
Away from all moving parts of the door.
7
.
Install the entrapment WARNING label next to the wall
button or console. Install the emergency release tag on, or
next to, the emergency release.
8
.
The operator must reverse when the door contacts a 1-1/2
inch high object on the floor at the center of the doorway.
This is about the size of a 2” x 4” board laid flat.