Gigabyte GA-VM800PMC Manual - Page 61

Configuring SATA Hard Drives - drivers xp

Get Gigabyte GA-VM800PMC PDF manuals and user guides View all Gigabyte GA-VM800PMC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

English 4-1-4 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3) Configure RAID set in RAID BIOS.(Note) (4) Make a floppy disk containing the SATA controller driver.(Note) (5) Install the SATA controller driver during OS installation.(Note) Before you begin Please prepare: (a) Two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID with the SATA controller, you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (1) Install SATA hard drive(s) in your system Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, you may refer to the motherboard user's manual to identify the SATA controller for the connector. Then connect the power connector from your power supply to the hard drive. (Note) Skip this step if you do not want to create RAID array on the SATA controller. - 61 - Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Appendix
- 61 -
English
4-1-4
Configuring SATA Hard Drive(s)
To configure SATA hard drive(s), follow the steps below:
(1)
Install SATA hard drive(s) in your system.
(2)
Configure SATA controller mode and boot sequence in BIOS Setup.
(3)
Configure RAID set in RAID BIOS.
(Note)
(4)
Make a floppy disk containing the SATA controller driver.
(Note)
(5)
Install the SATA controller driver during OS installation.
(Note)
Before you begin
Please prepare:
(a)
Two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard
drives with identical model and capacity). If you do not want to create RAID with the SATA
controller, you may prepare only one hard drive.
(b)
An empty formatted floppy disk.
(c)
Windows XP/2000 setup disk.
(d)
Driver CD for your motherboard.
(1)
Install SATA hard drive(s) in your system
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, you
may refer to the motherboard user's manual to identify the SATA controller for the connector. Then
connect the power connector from your power supply to the hard drive.
(Note)
Skip this step if you do not want to create RAID array on the SATA controller.